Runco VX-33I operation manual Service, HD Format

Page 73

Use the Service menu to access advanced projector configuration settings. This menu should be used by ISF-certified technicians only.

You must enter a passcode to access the Service menu.

Note

Test Video: Select Test Video from the Service Menu to access the internal test patterns

on the VX-33i. Four patterns are available: Horizontal Ramp, Vertical Ramp, Color Bars 1 (solid bars) and Color Bars 2 (SMPTE “checkerboard” pattern).

Press MENU to exit test pattern mode.

Tip

You can also use the PATTERN button on the projector rear panel

to enter and exit test pattern mode.

Service

Service

Test Video

Display Device

HD Format

Triggers

Miscellaneous

System Reset

Restore Saved Settings

Display Device: The options in the Display Device menu allow you to change the picture orientation and perform lens adjustments.

•Installation: Select Installation from the Display Device menu to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).

•Lens: Select Lens from the Display Device menu to access the motorized lens controls. Refer to Primary Lens Adjustments on page 37.

•Lamp Info: Select Lamp Info from the Display Device menu to obtain information

about the currently-installed lamp: its serial number, number of “strikes” (attempts to ignite) and number of hours in use.

•Diagnostic: Select Diagnostic from the Display Device menu, then select Red, Green, Blue, Yellow, Cyan or Magenta to display only that color (simulating a filter of that color). This can be useful for calibration or measurement purposes.

To restore the normal picture (all colors), select White.

HD Format: Select HD Format from the Service menu to choose the default color space for the source signals on the HD1, HD2 and HD3 inputs. Select COMP (component) or RGB. The DHD Controller assumes this color space when you “direct-select” an HD input using the left-arrow and right-arrow ( or ) buttons on the projector rear panel or DHD Controller front panel, or the HD1, HD2 or HD3 buttons on the remote control unit.

You can override this setting by using the OSD to select an HD input (refer to Input Source on page 47). For example, if you select COMP for HD2 here and the input signal changes to RGB, select “RGB BNC” from the Input Source menu to enable the VX-33i to properly display that signal.

Note

When you change the default color space for an HD input, it takes

effect the next time you select that input (not immediately).

HD Format

HD1 7 COMP … RGB

HD2

7 COMP

… RGB

HD3

… COMP

7 RGB

Runco VX-33i Installation/Operation Manual

57

Page 72 Page 74
Image 73
Page 72 Page 74
Contents VX-33i Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingSerial Communications Table of Contents Xiv List of Figures List of Figures Xvi About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories VX-33i at a Glance Controls and FunctionsVX-33i Rear Panel VX-33i Rear PanelLeft Button Power Input 100 to 240 VAC Connect the VX-33i to power hereService only For future use VX-33i Rear Connector PanelRS-232/485 Control Port Volt 750 mA Trigger OutputsHD3 Input Hdmi I 1 / Hdmi II 2 DigitalVX-33i Remote Control VX-33i Remote ControlOn / OFF Picture Adjustment Buttons BRT BrightnessSource Selection Buttons VID S-VideoAspect Ratio Selection Buttons Memory Preset Buttons169 Lbox LetterboxRemote Control InstallationStep Procedure For Details, Refer to Quick SetupIf installing a VX-33i/CineWide or VX-33i/CineWide Installation Type Installation ConsiderationsAmbient Light 96x54-inch Throw Range Throw Ratio Inches, with Lens OptionLens Lens Only Anamorphic Minimum Maximum Apollo B 134.40Floor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsOther Considerations Installing the Primary Projection LensPage Installing the Optional CineWide Lens Mount AutoScope Installing the AutoScope Lens Motor VX-33i/CineWide withRemove VX-33i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connecting Source Connector Panel AccessConnections to VX-33i11. Digital DTV RGB or Component Video Connections HD1, HD2 DTV or Progressive Component YPbPr Source 12. Digital DTV RGB or Component Video Connections HD313. Analog RGB Connections Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Video/Composite Video Connections See FigureConnection RS-232 ControllerTrigger Outputs to Connecting 12-voltExternal Equipment AutoScope Lens Motor RearConnecting to AC Power Connecting an External IRReceiver to Rear PanelAdjusting the Picture Orientation Turning on the PowerFocus Primary Lens AdjustmentsZoom Lens ShiftAssembly to Lens Motor Installing and Adjusting the CineWide Anamorphic LensCarriage Plate CineWide With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjust the Anamorphic Configure Lens MotorAdjusting the Horizontal X Lens Position TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Operation Using the On-Screen MenusService Memory PresetsInput Source Aspect RatioInput Source Main MenuAspect Ratio Select 169 to view 169 DVDs Remote Aspect Ratio Control Description Key 169Hdtv programs in their Native aspect ratioRemote Aspect Ratio Control Description Key PicturePicture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationCalibration ISF Night CalibrationISF Day Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format ISF Day/Night presets Lamp Replacement Maintenance and TroubleshootingSide Filter Access Panel Filter ReplacementSymptom Possible Causes Solution Troubleshooting TipsPage Serial Communications If you are using a PC to communicate withInput Selection Commands Command Description ResponseAspect Ratio Commands Menu Navigation Commands Command Description Response Image Preset CommandsPicture Adjust Commands Enter or Select buttonStatus Command Description Response Status Commands============================== Resolution 720P60 Page VX-33i Specifications SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsSpecifications are subject to change without notice VX-33i/CineWide with AutoScope Dimensions VX-33i DimensionsSupported Timings Horizontal Supported? √ = Yes, = No Format Resolution Frequency HD 1/HD 2/HDPage Page 020-1002-00 rev. a September
Top Page Image Contents