Runco CX-70DHD operation manual DHD Controller Front Panel

Page 21

Controls and Functions

1.RS-232 IN

Connect the Display Control output on the DHD Controller to this input (see Figure 2-4).

2.RS-232 OUT Not used.

3.ANALOG IN Not used.

4.DVI IN

Connect the HDMI output from the DHD Controller to this input.

5.DVI OUT Not used.

6.POWER INPUT

Connect the CX-70DHD to AC power here.

Figure 2-3shows the controls and indicators on the DHD Controller front panel; the paragraphs that follow describe them.

2.2

DHD Controller Front Panel

3

CX-70DHD

HDMI 1

16:91080i/60

11 10 9

		ra tio
	standby	nt	er
	i	nt
	i	e
	n
	p
	u
	t
		r atio

i n p u t

m

e n u

1

2

3

4

5

6

7

8

Figure 2-3. DHD Controller Front Panel

1.RUNCO ICON

Lights blue to indicate that the controller is on or powering up.

2.IR SENSOR

Receives IR commands from the remote control.

3.VACUUM FLUORESCENT DISPLAY

Can be used instead of the On-Screen Display (OSD). Displays currently-selected menu or – if no menu is selected – the connected display device model, current source, input resolution and aspect ratio.

4.ON/STANDBY BUTTON

Press once to toggle from standby mode to on mode. Press it again to return to standby mode. For a discrete on or off command, you can use the direct access buttons on the remote control.

CX-70DHD Installation/Operation Manual

7

Image 21

Contents CX-70DHD Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Industry Canada ICES-003 Page Table of Contents Specifications Maintenance and TroubleshootingOperation External ControlList of Figures List of Figures Xiv About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsCX-70DHD at a Glance STANDBY/ON Indicator Power SwitchRemote Control Sensor Display StandDHD Controller Front Panel Down Button Left ButtonRight Button Menu ButtonDHD Controller Rear Panel TriggersInputs 10. IR Main Power SwitchRS-232 / RS-485 Main AC FuseDHD Controller/CX-70DHD Remote Control CX-70DHD Remote Control UnitEnter IR Output IndicatorReturn / Exit LightSVC CinemaISF Night ISF DAYControls and Functions Remote Control InstallationQuick Setup Installation OverviewStep Procedure For Details, refer to Synchronization Issues Installation ConsiderationsAmbient Light VentilationInput Timing Possible Audio Latency milliseconds Possible Audio Latency for Various Input/Output TimingsOn a Wall or Table Stand Mounting the CX-70DHDQty Description Assembling and Installing the Table StandConnections to the CX-70DHD and DHD Controller Connecting CX-70DHD to the DHD ControllerConnecting the CX-70DHD to the DHD Controller Sections that follow Connecting SourceComponents to the DHD Hdmi Source Connections See FigureHdmi Source Connections DTV-Set-Top Box BD/DVD DTV-STBRgbhv Source Connections Computer RGB CamcorderVCR DVD/DTV STBGaming Console Camcorder Composite and S-Video Source ConnectionsConnection RS-232 Controller12. Connecting 12-volt Trigger Outputs Connecting 12-volt13. External IR Receiver Connection Connecting an External IR Receiver to the DHD ControllerInstallation Operation Turning on the Power Setting the Computer Display PropertiesOperation Using the On-Screen Menus Service Main MenuRunco Video Aspect Ratio Input SourceInput Source Aspect RatioRemote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation CalibrationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsCopy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Exit Operation 47 and ISF Day/Night Memory Presets Operation Cleaning Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartTo Input Position on Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keyUsing Discrete IR Codes Command BitsWith Toggle Bit = Hex Binary Function Start Remote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 DataEnter Specifications CX-70DHD SpecificationsCX-70DHD Specifications DHD Controller Specifications DHD Controller SpecificationsCX-70DHD Dimensions with Table Stand CX-70DHD DimensionsFormat Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Page 020-0925-01 Rev. B April