Runco CX-70DHD operation manual To Input Position on

Page 72

Maintenance and Troubleshooting

Table 5-1. Troubleshooting Chart (continued)

Symptom		Possible Cause(s)	Solution

The CX-70DHD and DHD	•	Faulty or incorrect video	• Ensure that the HDMI
Controller are both on, but		connection between the	output from the DHD
there is no picture and		DHD Controller and the	Controller is properly
on-screen menus do not		CX-70DHD.	connected to the DVI IN
appear.			input on the CX-70DHD
			(see Figure 3-4).

The display is on and menus	•	Incorrect source selection.	• Select the correct source.
appear, but there is no	•	Source component is not	• Turn on the source
picture.		turned on.	component.
	•	Source component is	• Check connections from
		connected incorrectly or	source component to DHD
		not at all.	Controller.

Image is too bright and/or lacks definition in the bright areas of the image.

• Contrast is set too high.

• Lower the contrast setting.

Image appears “washed out” and/or dark areas appear too bright.

Colors in the image are swapped; for example, reds appear blue or vice versa.

•Brightness is set too high.

•The Red/Pr, Green/Y or Blue/Pb outputs from the source are connected to the wrong inputs on the DHD Controller.

•Lower the brightness setting.

•Ensure that the source outputs are connected to the correct DHD Controller input.

RGB-HD images appear	•	Tracking and Phase	• Adjust Tracking and Phase
“noisy.”		settings need adjustment.	settings (refer to Input
			Position on page 45).

Computer images do not dis-	•	The resolution and	• Select a compatible
play correctly.		frequency of the video	resolution and vertical
		card in the computer are	frequency (refer to
		not compatible with the	Supported Timings on
		CX-70DHD.	page 70).

The image is too large or too	•	Image size needs	• Adjust the image size (refer
small.		adjusting.	to Input Position on
			page 45 or Output Shift
			on page 51).

58	CX-70DHD Installation/Operation Manual

Image 72

Contents CX-70DHD Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Industry Canada ICES-003 Page Table of Contents Maintenance and Troubleshooting SpecificationsOperation External ControlList of Figures List of Figures Xiv Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsCX-70DHD at a Glance Power Switch STANDBY/ON IndicatorRemote Control Sensor Display StandDHD Controller Front Panel Left Button Down ButtonRight Button Menu ButtonDHD Controller Rear Panel TriggersInputs Main Power Switch 10. IRRS-232 / RS-485 Main AC FuseCX-70DHD Remote Control Unit DHD Controller/CX-70DHD Remote ControlIR Output Indicator EnterReturn / Exit LightCinema SVCISF Night ISF DAYControls and Functions Installation Remote ControlQuick Setup Installation OverviewStep Procedure For Details, refer to Installation Considerations Synchronization IssuesAmbient Light VentilationPossible Audio Latency for Various Input/Output Timings Input Timing Possible Audio Latency millisecondsMounting the CX-70DHD On a Wall or Table StandAssembling and Installing the Table Stand Qty DescriptionConnecting CX-70DHD to the DHD Controller Connections to the CX-70DHD and DHD ControllerConnecting the CX-70DHD to the DHD Controller Connecting Source Sections that followComponents to the DHD Hdmi Source Connections See FigureHdmi Source Connections BD/DVD DTV-STB DTV-Set-Top BoxComputer RGB Camcorder Rgbhv Source ConnectionsVCR DVD/DTV STBGaming Console Composite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt 12. Connecting 12-volt Trigger OutputsConnecting an External IR Receiver to the DHD Controller 13. External IR Receiver ConnectionInstallation Turning on the Power Setting the Computer Display Properties OperationOperation Using the On-Screen Menus Service Main MenuRunco Video Input Source Aspect RatioInput Source Aspect RatioAspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation CalibrationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesCopied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Exit Operation 47 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting CleaningTroubleshooting Tips Troubleshooting ChartTo Input Position on Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keyUsing Discrete IR Codes Command BitsWith Toggle Bit = Hex Binary Function Start IR Command List Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller RC5 DataEnter Specifications CX-70DHD SpecificationsCX-70DHD Specifications DHD Controller Specifications DHD Controller SpecificationsCX-70DHD Dimensions CX-70DHD Dimensions with Table StandSupported Signal Timings by Input Format Resolution Frequency Rate Hz MHz KHzSupported Timings Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Page 020-0925-01 Rev. B April