Runco CX-70DHD operation manual Operation

Page 68

Operation

Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

•Language: Select Language from the Miscellaneous menu and press the up- or down-arrows to select the OSD Language (English, Français, Deutsch, Italiano, Español, Svenska, Traditional Chinese, Simplified Chinese, Português or Russian).

•OSD Timer: Select OSD Timer from the Miscellaneous menu to set the OSD Timer, which controls how long the menus remain on-screen after selecting them. Select from 5 to 60 seconds, in one-second increments. Or, set the timer to 0 (disabled) if you want the menus to remain on-screen indefinitely.

•OSD Messages: When you select a new aspect ratio, input source or memory preset, the DHD Controller briefly displays an on-screen message confirming your new selection. To prevent the display of these messages, select OSD Messages from the Miscellaneous menu to and set it to Off.

•Blank Screen Color: Select Blank Screen Color from the Miscellaneous menu to select the color that appears when no incoming signal is present. The range is from 0 to 255 inclusive for each color component (red, green and blue).

•Sidebar Color: Select Sidebar Color from the Miscellaneous menu to change the color of the inactive image area. The range is from 0 to 255 inclusive for each color component (red, green and blue). The inactive image area is on either side of the active image area when using the 4:3 aspect ratio.

•Film Mode: Use Film Mode to smooth out moving images from interlaced, standard-definition (SD) sources. In most cases, the CX-70DHD detects the proper “pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing you may want to enable Film Mode to ensure stable processing for that source.

•CUE (Chroma Upsampling Error) Correction: Some DVD players use MPEG decoders that do not correctly “upsample” the 4:2:0 format chroma information on the DVD to the 4:2:2 or 4:4:4 format required by the video encoder of the display device.

This so-called “chroma bug” sometimes causes streaky or spiky horizontal lines running through the chroma channel. It is most noticeable in static, interlaced scenes and on diagonal edges (especially red ones). Set CUE to On to correct this issue.

Sync Threshold: Select Sync Threshold to adjust the threshold at which negative pulses on the component video green/luma channel are interpreted to be sync pulses.

Sync Threshold adjustment is occasionally necessary when a DVD player or HDTV source signal drops “below black” (for example, during scenes with explosions or when subtitles are present) and causes the display device to temporarily lose sync. If the sync level from the source is persistently too low, the display device won’t sync with the source at all.

The range is from 0 (approximately 60 millivolts (mV)) to 15 (approximately 256 mV).

54

CX-70DHD Installation/Operation Manual

Page 67 Page 69
Image 68
Page 67 Page 69
Contents CX-70DHD Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Industry Canada ICES-003 Page Table of Contents Maintenance and Troubleshooting SpecificationsOperation External ControlList of Figures List of Figures Xiv Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories CX-70DHD at a Glance Controls and IndicatorsControls and Functions Power Switch STANDBY/ON IndicatorRemote Control Sensor Display StandDHD Controller Front Panel Left Button Down ButtonRight Button Menu ButtonInputs DHD Controller Rear PanelTriggers Main Power Switch 10. IRRS-232 / RS-485 Main AC FuseCX-70DHD Remote Control Unit DHD Controller/CX-70DHD Remote ControlIR Output Indicator EnterReturn / Exit LightCinema SVCISF Night ISF DAYControls and Functions Installation Remote ControlStep Procedure For Details, refer to Quick SetupInstallation Overview Installation Considerations Synchronization IssuesAmbient Light VentilationPossible Audio Latency for Various Input/Output Timings Input Timing Possible Audio Latency millisecondsMounting the CX-70DHD On a Wall or Table StandAssembling and Installing the Table Stand Qty DescriptionConnecting CX-70DHD to the DHD Controller Connections to the CX-70DHD and DHD ControllerConnecting the CX-70DHD to the DHD Controller Connecting Source Sections that followComponents to the DHD Hdmi Source Connections See FigureHdmi Source Connections BD/DVD DTV-STB DTV-Set-Top BoxComputer RGB Camcorder Rgbhv Source ConnectionsGaming Console VCRDVD/DTV STB Composite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt 12. Connecting 12-volt Trigger OutputsConnecting an External IR Receiver to the DHD Controller 13. External IR Receiver ConnectionInstallation Turning on the Power Setting the Computer Display Properties OperationOperation Using the On-Screen Menus Runco Video ServiceMain Menu Input Source Aspect RatioInput Source Aspect RatioAspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsShould be used by ISF-certified technicians only InformationCalibration CIE 1931 Chromaticity Diagram Color Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesCopied settings are not retained after a power cycle Copy/PasteInput Names ServiceService Exit Operation 47 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting CleaningTroubleshooting Tips Troubleshooting ChartTo Input Position on Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keyWith Toggle Bit = Hex Binary Function Start Using Discrete IR CodesCommand Bits IR Command List Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller RC5 DataEnter CX-70DHD Specifications SpecificationsCX-70DHD Specifications DHD Controller Specifications DHD Controller SpecificationsCX-70DHD Dimensions CX-70DHD Dimensions with Table StandSupported Signal Timings by Input Format Resolution Frequency Rate Hz MHz KHzSupported Timings Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Page 020-0925-01 Rev. B April
Top Page Image Contents