Runco CX-70DHD operation manual Exit

Page 67

Operation

When you change a remote code on the CX-70DHD, you must re-program the

CX-70DHD remote control to send that same code. To do this:

1.Press and hold the LIGHT button on the remote control for approximately three seconds, or until the LED on the remote lights solid red.

2.Enter a new two-digit code between 00 and 31 inclusive. Include a leading zero for single-digit codes; for example, enter 9 as “09.”

RETURN

EXIT

3.The LED turns off to confirm the code change. If you enter an invalid code, the LED flashes for three or four seconds. Try again, entering a valid code.

•COMP Key Source: Select COMP Key Source from the Remote Control menu to assign the COMP remote control button to either the Component or SCART input.

Display Device - Configure: The options in the Display Device - Configure menu allow you to change the picture orientation, perform lens adjustments or access other, display-device specific functions.

•Installation – Orientation: Select Installation from the Display Device - Configure menu, then select Orientation to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).

•Diagnostics: Select Diagnostics from the Display Device - Configure menu, then select Red, Green, Blue, Yellow, Cyan or Magenta to display only that color channel (simulating a filter of that color). This can be useful for calibration or measurement purposes.

To restore the normal picture (all colors), select White.

Color Space: Select Color Space from the Service menu to choose the color space of the source signal for HDMI, RGB, and component connections.

•The default setting, Auto, functions as follows:

•HDMI: If the Auxiliary Video Information (AVI) infoframe contains color space and/or range data, the CX-70DHD uses that information. Otherwise, for RGB sources, the CX-70DHD uses the RGB-Videocolor space. For component SDTV and EDTV resolutions, REC601 is used. For other component video resolutions, REC709 is used.

•RGB: If Hsync or Vsync signals are present, the CX-70DHD uses the RGB-PCcolor space. Otherwise, REC601 is used for SDTV and EDTV sources, and REC709 for all other sources.

•Component: For SDTV and EDTV resolutions, the CX-70DHD uses the REC601 color space. For all other resolutions, REC709 is used.

In most cases, the Auto setting determines the correct color space to use. If it does not, you can force the CX-70DHD to use a specific color space. Choose one of the following:

•REC709 sets the color space matrix to that defined in ITU-R BT.709.

•REC601 sets the color space matrix to that defined in ITU-R BT.601.

•RGB-PCuses RGB color space and sets black at 0,0,0 RGB and white at 255,255,255 RGB, assuming an 8-bit image.

•RGB-Videouses RGB color space and sets black at 16,16,16 RGB and white at 235,235,235, assuming an 8-bit image, to correspond to the luminance values defined in digital component standards.

CX-70DHD Installation/Operation Manual

53

Page 66 Page 68
Image 67
Page 66 Page 68
Contents CX-70DHD Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Industry Canada ICES-003 Page Table of Contents External Control Maintenance and TroubleshootingSpecifications OperationList of Figures List of Figures Xiv About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsCX-70DHD at a Glance Display Stand Power SwitchSTANDBY/ON Indicator Remote Control SensorDHD Controller Front Panel Menu Button Left ButtonDown Button Right ButtonTriggers DHD Controller Rear PanelInputs Main AC Fuse Main Power Switch10. IR RS-232 / RS-485DHD Controller/CX-70DHD Remote Control CX-70DHD Remote Control UnitLight IR Output IndicatorEnter Return / ExitISF DAY CinemaSVC ISF NightControls and Functions Remote Control InstallationInstallation Overview Quick SetupStep Procedure For Details, refer to Ventilation Installation ConsiderationsSynchronization Issues Ambient LightInput Timing Possible Audio Latency milliseconds Possible Audio Latency for Various Input/Output TimingsOn a Wall or Table Stand Mounting the CX-70DHDQty Description Assembling and Installing the Table StandConnections to the CX-70DHD and DHD Controller Connecting CX-70DHD to the DHD ControllerConnecting the CX-70DHD to the DHD Controller Hdmi Source Connections See Figure Connecting SourceSections that follow Components to the DHDHdmi Source Connections DTV-Set-Top Box BD/DVD DTV-STBRgbhv Source Connections Computer RGB CamcorderDVD/DTV STB VCRGaming Console Camcorder Composite and S-Video Source ConnectionsConnection RS-232 Controller12. Connecting 12-volt Trigger Outputs Connecting 12-volt13. External IR Receiver Connection Connecting an External IR Receiver to the DHD ControllerInstallation Operation Turning on the Power Setting the Computer Display PropertiesOperation Using the On-Screen Menus Main Menu ServiceRunco Video Aspect Ratio Input SourceAspect Ratio Input SourceHdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsCalibration InformationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsCopy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Exit Operation 47 and ISF Day/Night Memory Presets Operation Troubleshooting Chart Maintenance and TroubleshootingCleaning Troubleshooting TipsTo Input Position on Serial Communications Port ConfigurationSerial Command Syntax External ControlInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Enter keyCommand Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start RC5 Data IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD ControllerEnter CX-70DHD Specifications SpecificationsCX-70DHD Specifications DHD Controller Specifications DHD Controller SpecificationsCX-70DHD Dimensions with Table Stand CX-70DHD DimensionsSupported? √ = Yes, = No Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported TimingsPAL-B/G/H/I PAL-M Page 020-0925-01 Rev. B April
Top Page Image Contents