Runco CX-70DHD operation manual Color Temperature Presets and Associated Color Points

Page 64

Operation

Table 4-2lists the x- and y-coordinates for each color temperature preset.

Table 4-2. Color Temperature Presets and Associated Color Points

Color Temperature Preset

Associated x/y Values

 

 

x

y

 

 

 

 

3200K

0.423

0.404

 

 

 

5500K

0.332

0.348

 

 

 

6500K

0.313

0.329

 

 

 

•Backlight: The Backlight control changes the apparent brightness of the displayed image. Its effect is similar to that of a lamp intensity control on a projector. Use a higher setting for rooms with a lot of ambient light. Use a lower setting for more “theater-like” viewing conditions (little or no ambient light).

Tip

To prolong the life of the display, set the Backlight only as high as is

necessary to produce the desired brightness.

Input Image: The Input Image controls are functionally similar to those in the Picture menu (refer to page 40), but are accessible only by entering the Calibration menu passcode.

The Input Image settings establish the “zero point” for the Picture

Note menu settings, whose values represent offsets from the Input Image settings. For example, if you set Brightness to 10 in this menu, setting Brightness to 10 in the Picture menu results in an actual setting value of 20 (10+10).

Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but adjust the color balance of the incoming signal. These settings are also saved independently for each input and display mode.

•Gain/Offset (HD1, HD2 and Component/SCART inputs only): These controls operate similarly to those in the Display Color menu (described on page 48), but affect the Y, Pb and Pr signal components rather than the red, green and blue channels.

•Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a Composite or S-Video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them.

•Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

Save ISF Night/Save ISF Day: Whenever you make a change to the ISF settings, you should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to do this.

50

CX-70DHD Installation/Operation Manual

Page 63 Page 65
Image 64
Page 63 Page 65
Contents CX-70DHD Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Industry Canada ICES-003 Page Table of Contents Maintenance and Troubleshooting SpecificationsOperation External ControlList of Figures List of Figures Xiv Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsCX-70DHD at a Glance Power Switch STANDBY/ON IndicatorRemote Control Sensor Display StandDHD Controller Front Panel Left Button Down ButtonRight Button Menu ButtonTriggers DHD Controller Rear PanelInputs Main Power Switch 10. IRRS-232 / RS-485 Main AC FuseCX-70DHD Remote Control Unit DHD Controller/CX-70DHD Remote ControlIR Output Indicator EnterReturn / Exit LightCinema SVCISF Night ISF DAYControls and Functions Installation Remote ControlInstallation Overview Quick SetupStep Procedure For Details, refer to Installation Considerations Synchronization IssuesAmbient Light VentilationPossible Audio Latency for Various Input/Output Timings Input Timing Possible Audio Latency millisecondsMounting the CX-70DHD On a Wall or Table StandAssembling and Installing the Table Stand Qty DescriptionConnecting CX-70DHD to the DHD Controller Connections to the CX-70DHD and DHD ControllerConnecting the CX-70DHD to the DHD Controller Connecting Source Sections that followComponents to the DHD Hdmi Source Connections See FigureHdmi Source Connections BD/DVD DTV-STB DTV-Set-Top BoxComputer RGB Camcorder Rgbhv Source ConnectionsDVD/DTV STB VCRGaming Console Composite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt 12. Connecting 12-volt Trigger OutputsConnecting an External IR Receiver to the DHD Controller 13. External IR Receiver ConnectionInstallation Turning on the Power Setting the Computer Display Properties OperationOperation Using the On-Screen Menus Main Menu ServiceRunco Video Input Source Aspect RatioInput Source Aspect RatioAspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsCalibration InformationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesCopied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Exit Operation 47 and ISF Day/Night Memory Presets Operation Maintenance and Troubleshooting CleaningTroubleshooting Tips Troubleshooting ChartTo Input Position on Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keyCommand Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start IR Command List Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller RC5 DataEnter CX-70DHD Specifications SpecificationsCX-70DHD Specifications DHD Controller Specifications DHD Controller SpecificationsCX-70DHD Dimensions CX-70DHD Dimensions with Table StandSupported Signal Timings by Input Format Resolution Frequency Rate Hz MHz KHzSupported Timings Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Page 020-0925-01 Rev. B April
Top Page Image Contents