Runco CX-70DHD Quick Setup, Installation Overview, Step Procedure For Details, refer to

Page 30

Installation

3.2

Quick Setup

•Do not drop the remote control or expose it to moisture or high temperature.

•The remote control may malfunction under a fluorescent lamp. If that occurs, move the plasma display away from the fluorescent lamp.

•Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the plasma display.

Note

The signal from the remote control can be reflected by walls or

other surfaces.

•If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.

•Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the plasma display and repeat the operation.

Table 3-1gives a quick overview of the CX-70DHD installation process. The sections following this one provide detailed instructions.

 

Note

Installation must be performed by a qualified custom video

 

installation specialist.

 

Table 3-1. Installation Overview

 

 

 

 

 

 

Step

 

 

Procedure

For Details, refer to

 

 

page...

 

 

 

 

 

 

 

 

1

 

Mount the CX-70DHD on a wall or table stand

19

 

 

 

 

2

 

Connect the DHD Controller to the CX-70DHD

21

 

 

 

 

3

 

Connect signal sources to the DHD Controller

23

 

 

 

 

4

 

Connect external controller to DHD Controller RS-232 port

29

 

 

(optional)

 

 

 

 

 

 

5

 

Apply power to the CX-70DHD

33

 

 

 

 

6

 

If using the CX-70DHD with a computer, adjust computer

33

 

 

display properties

 

 

 

 

 

7

 

Display calibration: adjust the following for each input and

40

 

 

display mode (resolution and frame rate); save settings

 

 

 

when finished:

 

 

 

• Aspect ratio

 

 

 

 

• Brightness

 

 

 

 

• Contrast

 

 

 

 

• Color level

 

 

 

 

• Tint

 

 

 

 

• Sharpness

 

 

 

 

• White Balance

 

 

 

 

 

 

16

CX-70DHD Installation/Operation Manual

Page 29 Page 31
Image 30
Page 29 Page 31
Contents CX-70DHD Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Industry Canada ICES-003 Page Table of Contents Operation Maintenance and TroubleshootingSpecifications External ControlList of Figures List of Figures Xiv Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsCX-70DHD at a Glance Remote Control Sensor Power SwitchSTANDBY/ON Indicator Display StandDHD Controller Front Panel Right Button Left ButtonDown Button Menu ButtonDHD Controller Rear Panel TriggersInputs RS-232 / RS-485 Main Power Switch10. IR Main AC FuseCX-70DHD Remote Control Unit DHD Controller/CX-70DHD Remote ControlReturn / Exit IR Output IndicatorEnter LightISF Night CinemaSVC ISF DAYControls and Functions Installation Remote ControlQuick Setup Installation OverviewStep Procedure For Details, refer to Ambient Light Installation ConsiderationsSynchronization Issues VentilationPossible Audio Latency for Various Input/Output Timings Input Timing Possible Audio Latency millisecondsMounting the CX-70DHD On a Wall or Table StandAssembling and Installing the Table Stand Qty DescriptionConnecting CX-70DHD to the DHD Controller Connections to the CX-70DHD and DHD ControllerConnecting the CX-70DHD to the DHD Controller Components to the DHD Connecting SourceSections that follow Hdmi Source Connections See FigureHdmi Source Connections BD/DVD DTV-STB DTV-Set-Top BoxComputer RGB Camcorder Rgbhv Source ConnectionsVCR DVD/DTV STBGaming Console Composite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt 12. Connecting 12-volt Trigger OutputsConnecting an External IR Receiver to the DHD Controller 13. External IR Receiver ConnectionInstallation Turning on the Power Setting the Computer Display Properties OperationOperation Using the On-Screen Menus Service Main MenuRunco Video Input Source Input SourceAspect Ratio Aspect RatioSelect 169 to view 169 DVDs Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Hdtv programs in theirRemote Aspect Ratio Control Description Key OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation CalibrationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesCopied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Exit Operation 47 and ISF Day/Night Memory Presets Operation Troubleshooting Tips Maintenance and TroubleshootingCleaning Troubleshooting ChartTo Input Position on External Control Port ConfigurationSerial Command Syntax Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keyUsing Discrete IR Codes Command BitsWith Toggle Bit = Hex Binary Function Start RC5 Control Codes for the DHD Controller IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 DataEnter Specifications CX-70DHD SpecificationsCX-70DHD Specifications DHD Controller Specifications DHD Controller SpecificationsCX-70DHD Dimensions CX-70DHD Dimensions with Table StandSupported Timings Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Page 020-0925-01 Rev. B April
Top Page Image Contents