Runco CX-70DHD operation manual Service, Input Names

Page 66

Service ➤

Service

Test Video

Input Names

Remote Control

Display Device

Color Space

Triggers

Miscellaneous

Sync Threshold

HDMI EDID Extension

Front Panel Brightness

System Reset

OSD Position: To adjust the position of the OSD, select OSD Position from the Calibration menu and press ENTER.

Press or to select “Hor.” or “Ver.” Then, press or to change the position.

Use the Service menu to access advanced display configuration settings. This menu

should be used by ISF-certified technicians only.

You must enter a passcode to access the Service menu.

Note

Test Video: Select Test Video from the Service Menu to access the internal test patterns

on the CX-70DHD. Four patterns are available: Horizontal Ramp, Vertical Ramp, Color Bars 1 (solid bars) and Color Bars 2 (SMPTE “checkerboard” pattern).

Press MENU to exit test pattern mode.

Input Names

 

 

 

 

 

 

 

Restore

C

o

m p o s i

t e

Composite

 

 

 

 

 

 

 

S

- V i d e o

1

S-Video 1

S

-

V i d e o

2

S-Video 2

C

o

m p

o n e n t

Component

H

D

1

 

 

 

HD 1

H

D

2

 

 

 

HD 2

S

C

A

R

T

 

 

SCART

H

D

M

I

 

1

 

HDMI 1

H

D

M

I

 

2

 

HDMI 2

 

 

 

 

 

 

 

 

Input Names: You can give each DHD Controller input a descriptive name. For example, you may want to change the default input name to the type of source component connected to it: “VCR,” “DVD,” “Laptop” et cetera. Input names can be up to 12 characters long.

To edit an input name, select Input Names from the Service menu. Press or to select an input and press ENTER. Use the or buttons to change a character; press

or to select a character to change. When you have finished editing the input name, press ENTER or MENU.

To restore the default input name, press repeatedly to highlight that input name in the “Restore” column. Then, press ENTER.

Remote Control: Select Remote Control from the Service menu to change the following settings related to remote control operation.

•Remote Code: Select Remote Code from the Remote Control menu to set the infrared (IR) code set to which the CX-70DHD will respond. By default, it is set to 17. You can change this setting if either:

•Another device in the theater (a DVD player, for example) is responding to commands from the CX-70DHD remote control (Figure 2-5)in ways that are unpredictable or undesirable.

•You have multiple DHD Controllers and want to control them independently, as opposed to broadcasting commands from a single remote to all of them. In this scenario, you can use multiple remotes programmed to use different IR codes. Or, you can use a single remote and change the IR code as needed to address a specific DHD Controller.

Use the DHD Controller front-panel keypad to change the IR code to Tip which the controller will respond. Then, change the code sent by the

remote to match as described below.

52

CX-70DHD Installation/Operation Manual

Page 65 Page 67
Image 66
Page 65 Page 67
Contents CX-70DHD Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Industry Canada ICES-003 Page Table of Contents Operation Maintenance and TroubleshootingSpecifications External ControlList of Figures List of Figures Xiv Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsCX-70DHD at a Glance Remote Control Sensor Power SwitchSTANDBY/ON Indicator Display StandDHD Controller Front Panel Right Button Left ButtonDown Button Menu ButtonDHD Controller Rear Panel TriggersInputs RS-232 / RS-485 Main Power Switch10. IR Main AC FuseCX-70DHD Remote Control Unit DHD Controller/CX-70DHD Remote ControlReturn / Exit IR Output IndicatorEnter LightISF Night CinemaSVC ISF DAYControls and Functions Installation Remote ControlQuick Setup Installation OverviewStep Procedure For Details, refer to Ambient Light Installation ConsiderationsSynchronization Issues VentilationPossible Audio Latency for Various Input/Output Timings Input Timing Possible Audio Latency millisecondsMounting the CX-70DHD On a Wall or Table StandAssembling and Installing the Table Stand Qty DescriptionConnecting CX-70DHD to the DHD Controller Connections to the CX-70DHD and DHD ControllerConnecting the CX-70DHD to the DHD Controller Components to the DHD Connecting SourceSections that follow Hdmi Source Connections See FigureHdmi Source Connections BD/DVD DTV-STB DTV-Set-Top BoxComputer RGB Camcorder Rgbhv Source ConnectionsVCR DVD/DTV STBGaming Console Composite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt 12. Connecting 12-volt Trigger OutputsConnecting an External IR Receiver to the DHD Controller 13. External IR Receiver ConnectionInstallation Turning on the Power Setting the Computer Display Properties OperationOperation Using the On-Screen Menus Service Main MenuRunco Video Input Source Input SourceAspect Ratio Aspect RatioSelect 169 to view 169 DVDs Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Hdtv programs in theirRemote Aspect Ratio Control Description Key OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation CalibrationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesCopied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Exit Operation 47 and ISF Day/Night Memory Presets Operation Troubleshooting Tips Maintenance and TroubleshootingCleaning Troubleshooting ChartTo Input Position on External Control Port ConfigurationSerial Command Syntax Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keyUsing Discrete IR Codes Command BitsWith Toggle Bit = Hex Binary Function Start RC5 Control Codes for the DHD Controller IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 DataEnter Specifications CX-70DHD SpecificationsCX-70DHD Specifications DHD Controller Specifications DHD Controller SpecificationsCX-70DHD Dimensions CX-70DHD Dimensions with Table StandSupported Timings Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Page 020-0925-01 Rev. B April
Top Page Image Contents