Runco CR-32HD, CR-40HD Basic Operations, Connecting the Power Cord and Switching Display On / Off

Page 17

Basic Operations

1.Connect the power cord for your display to the power input on the back of your display.

2.Plug the power cord for the display into a nearby outlet.

3.Press the POWER ( ) button on the remote control or the POWER button on the display panel.

4. To switch your display off, press the POWER () button on the remote control or the POWER button on the display panel.

OFFON

1 2 3

4 5 6

7 8 9

100

 

0

TIMER

 

OFF

 

SOURCE

 

INPUT

INPUT

INPUT

INPUT

1

2

3

4

Connecting the Power

Cord and Switching the

Display On / Off

1.

Press the MENU button on the remote control.

Selecting a Source

2.

Press the ▲▼ buttons to select Source and then press the ENTER or ► button.

 

3.

Select the appropriate Source by pressing the ▲▼ buttons and then press the

 

 

ENTER or ► button.

 

 

• You can select TV, Input 1, Input 2, Input 3, Input 4, DVI or RGB.

 

4.

Press the MENU button to return to the previous menu.

 

 

OR

 

You can also select the Source directly from the remote control using discrete source buttons.

Runco CR-32HD

Source

Aspect Ratio

Picture Adjust

Audio

Channel

Timer

Setup

ISF Calibration

>TV Input 1 Input 2 Input 3 Input 4

DVI RGB

100

 

0

TIMER

 

OFF

 

SOURCE

 

INPUT

INPUT

INPUT

INPUT

1

2

3

4

DVI

 

RGB

TV

 

HD

 

 

 

SLEEP

MEMORY

DISPLAY

CUST

 

ISF

ISF

 

NT

DAY

 

 

17

Image 17
Contents CR-32HD / CR-40HD Table of Contents RS-232 Configurations ISF Calibration ServiceSignals Supported Pin Configuration PC/DVIWhat is Covered Under the Terms of this Limited Warranty One Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Introduction DOC compliance Notice PrecautionsFront View Power Indicator StatusCR-32HD and CR-40HD Input2 CR-32HD Rear View Input Panel13 14 CR-40HD Rear View Input Panel100 Remote ControlOr INPUT2 Connecting to the VideoConnections Connecting to a DVD or DTV Set-Top Box Input RCA or DVI Using the Monitor OUT featureTo use the display as a PC Monitor Connecting to a PCSetting the PC Properties Connecting Headphones Basic Operations Connecting the Power Cord and Switching Display On / OffStandard 43 mode Anamorphic modeLetterbox mode Virtualwide modePress the Menu button on the remote control Selecting Picture AdjustSave Settings Restore SettingsSelecting Channel Selecting AudioSelecting Timer OSD Language SetupPC Mode Adjust CC1 CC2 CC3 CC4 Text1 Text2 Text3 Text4 Parental Control CaptionOverscan Input SelectionMonitor Out Picture Adjust ISF Calibration ServiceISF Calibration White BalanceCommand Ack Blue Enable DNR Digital Noise ReductionFactory Reset GammaSmall Twin Off Picture in Picture PIPDisplaying the Picture in Picture PIP Changing the PIP Position Selecting the Image Mode in the PIPChanging the PIP Size Selecting the Image Size in the PIPSwapping the Main & Sub-Sound Swapping the Main & Sub-PictureChanging the PIP Aspect Ratio Wide 169 modeListening to Stereo Sound / SAP Stereo Sound / SAPOption BroadcastingPin 1 Ground RS-232 ConfigurationsRS-232C Configurations Serial Protocol ‘\n’Timer OFF Mode Freq Hz Freq KHz Signals SupportedDVI-D Connector Pin Configuration PC/DVIPC Input Connector D-Sub 15Pin For Display Panel TroubleshootingFor Monitor CR-32HD SpecificationsCR-40HD DimensionsRUMA-011095