Zenith HCS5610 warranty Clone Programmer Learning Setup, Learn Setup from Master TV/STB

Page 51

Clone Programmer Learning Setup

Learning the Master TV Setup

Instructions for the Clone Programmer to Learn the Master TV/STB Setup.

Use MPI Cable to Connect LT2002 Clone Programmer to Master TV/STB MPI Port

If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote.

Learn Setup from Master TV/STB

Press 1 to select the “LEARN FROM TV” option, then press ON/OFF, POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the Memory ”Bank” you want to store the master TV/STB’s setup in by pressing either Channel key repeatedly to choose Memory 1, 2 or 3. (If you choose a Memory “Bank” that has a master device’s setup programmed into it, that setup will be overwritten by the new master TV/STB’s setup.) Once the Clone memory bank is selected, press ON/OFF, POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master TV/STB’s setup.

Set the Clock (Optional)

Set the time on a Master TV’s Clock. (If the time has already been copied from a TV into the Clone programmer, you can set a master TV’s clock by copying the time from the Clone programmer.) The Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.)

Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I. input capability.

After the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a master TV, or another TV which has already had the features set up.)

*Notes: When using the clone programmer for teaching or learning,

be sure that the heartbeat pattern is shown on the LEDs. Both learning and teaching should take about 45 or more seconds depending on the complexity of the master setup. While the clone is functioning, do not move it or otherwise disturb the clone or wiring connections. If the clone finishes the function in less than 45 seconds, redo the function again. Press the reset button if the clone does not act normally.

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION

XX

THE TV IS VERSION

XX

THE SW IS REVISION

XX

CLONE CLOCK=

XX:XX

TV CLOCK=

XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

This menu should appear by itself after the LT2002 is connected to the TV/STB MPI port.

CLONE SELECTION MENU

(1)LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER

LT2002 Clone Programmer Communication Problems

•A slow flashing green light indicates there are communication problems between the TV/STB and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.

•If the status indicator is red, the programmer batteries are low and should be replaced. Install 4 high-quality alkaline AA batteries.

P A G E 5 1

Page 50 Page 52
Image 51
Page 50 Page 52
Contents B l e o f c o n t e n t s Installer quick setup guide Installation and Operating Guide WarrantySerial no Record the Model NumberMillbrook Drive Lincolnshire, IL 60069, USA. Phone G ENEC National Electrical Code Important Safety InstructionsTable of Contents Setup Checklist Status LED flashes while the program is running Installation/Connections OverviewMonitor Ventilation VentilationMonitor/Integrator Box Wall Mounting System Ventilation / Installation OverviewIR Receiver & IR Bracket Installation AUX Controller Connection and PlacementAntenna Hookup G E 1Mini glossary Connect cable service to the HD Integrator Box System Cable Service HookupRS-232C Control Connections Connect Aux Control IR Output as required of your system Viewing Equipment SetupComputer PC Hookup DVI DVI Hookup to RJP or DVD PlayerTV/Monitor TV/Monitor RJP ConnectionsAudio Connection Digital Audio Optical Connections On-Screen Menus Overview Info Other Menus & On-Screen DisplaysG E 2 User Remote Control Key FunctionsChannel -/+ Installer Remote Control Key FunctionsNumber Keypad MuteAuto Program Channel Search Channel List Channel ListChannel Control Press the ADJ F or G button to adjust Signal being receivedOK Enter button On-Off Timers Setup Clock SetupSee the next Enter buttonUse the ADJ D E F G buttons to set the Daylight Savings Time Zone options for your local areaPress the OK Enter button Use the ADJ D or E button to highlight Time Zone and pressUse the ADJ F or G button to select the Time Zone Use the ADJ D or E button to highlight the Daylight SavingYou can set a time for the TV to automatically turn-off You can set a time for the TV to automatically turn-onUse the ADJ D E F G buttons to choose AM / PM, Hours Minutes and time period to turn-onUse the ADJ D or E button to highlight Auto Off and press Use the ADJ D or E button to choose On or OffG E 3 OK Enter button ChipUse the ADJ D or E button to choose 1~12 hours and press Enter the 4 digits passwordThis option sets up hour that you wish to block Use the ADJ D or E button to highlight Set Block HourUse the ADJ D E F G buttons to choose and set up the menu Options for Tvpg RatingDescription of the TV FCC Rating Codes Options for Mpaa Rating Description of the Mpaa and TV FCC Rating CodesUse the ADJ D or E button to highlight the Mpaa Rating Options for Can. English Rating Enter the 4digits passwordUse the ADJ D or E button to highlight the Can. English Rating and press the OK Enter buttonUse the ADJ D or E button to highlight the Can. French Options for Can. French RatingCanadian French Ratings E Expect No restriction. G For all Dim3 and press the OK Enter button Will be available only for digital channel signalThis function operates only when TV has received Use the ADJ D or E button to highlight the D/L RatingPress OK Enter button When finished, press Menu repeatedly to removeCaption Menu To highlight the Caption menu and press the OK EnterUse the ADJ D E F G buttons to customize each option Font Use the ADJ D or E button to highlight Digital ModeUse the ADJ D or E button to choose Service 1-Service Customize the digital captions that appear on your screenG E 4 Sound MenuUse the ADJ D or E button to highlight Digital Output Use the ADJ D / E buttons to choose Dolby Digital or PCMUse the ADJ D or E button to highlight Auto Volume To highlight the Sound menu and press the OK EnterUse the ADJ D or E button to choose Mono, Stereo or SAP French and press the OK Enter button Use the ADJ D or E button to choose English, Spanish orUse the ADJ D or E button to highlight Menu Language Language ControlUse the ADJ D or E button to highlight and set the Menu Language English, Español or FrançaisUse the ADJ D or E button to choose 1-99 numbers and press Set IDPicture Menu Color Temperature and press the OK Enter buttonUse the ADJ D or E button to choose Screen Format Buttons to set your own settings for the options. WhenUse the ADJ D or E button to choose a preset screen Finished, press the Menu buttonUse the ADJ D or E button to choose Noise Reduction Use the ADJ D or E button to choose Film Mode and pressTypical Installer Menu Commercial Mode Setup If batteries are removed, the Clone Clock time will be lost Cloning Connections/Learning SetupTurn to the next page to continue Cloning Setup G E 5Clone Programmer Learning Setup Learn Setup from Master TV/STBSet the Clock Optional Cloning Connections / Teaching Setup Teach Master TV/STB’s Setup to the targetDisconnect TV/STB Power for 15 Seconds Installer Menu Items 000 through Installer MenuAccessing the Installer’s Menu Using the Installer’s MenuInstaller Menu Items 035 through Installer Sequence Detailed Descriptions of Installer Menu ItemsPoll Rate Mute DisableSleep Timer Caption LockRJP Available AUX StatusVID OUT Format Atsc Tune ModeAtsc Band Start Minor ChannelReference TV Features / Menus that can be Cloned Channel Picture Sound Setup CaptionFilm Mode Changing Source Labels on Master TV Adding Channel Icons and Labels in the 2-5-4 + Menu ModeTo Do Channel Editing/Labeling, proceed as follows Changing/Adding Channel Labels on Master TVDetailed Instructions Reference Detailed Information For Making a Master TVReference Software Version Check Procedure to Check Software VersionTV/STB Aux Input Configuration TV/STB Aux Input ConfigurationTV/STB RS-232 Monitor Requirements / RS-232 Troubleshooting Type of Connector D-Sub 9-Pin FemaleDisplays ‘No Signal’ message at Power Off Transmission / Receiving Protocol Connecting the cableRS-232C Control Communication ParameterSet ID OKDatax KeyCommand m cTo send IR remote key code Mc Set ID DataCr Data Key code Refer to page A18Troubleshooting Reference Cloning Procedure Troubleshooting Reset Clone After Static ShockClone Programmer Troubleshooting Troubleshooting Flow Chart G E 7 Installer Quick Setup GuideOHM RF Cable Glossary of TermsOWNER’S Responsibility For Customer Support/Service Please callCopyright 2008 LG Electronics U.S.A., Inc LG’S Responsibility
Top Page Image Contents