Zenith HCS5610 warranty Record the Model Number, Serial no

Page 2

For Customer Support/Service please call:

1-888-865-3026

www.zenith.com

www.lgcommercial.com

RECORD THE MODEL NUMBER

The model and serial number of this HD Integrator Box System are located on the side of the cabinet. For future reference, we suggest that you record the serial number here:

MODEL NO. HCS5610

SERIAL NO.____________________________________

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

IT IS FORBIDDEN TO CONNECT THIS TV TO ANY TELECOMMUNICATION NETWORK / TELEPHONE.

NOTE TO CABLE TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

2000 Millbrook Drive, Lincolnshire, IL 60069.

Image 2
Contents Installation and Operating Guide Warranty B l e o f c o n t e n t s Installer quick setup guideRecord the Model Number Serial noG E Millbrook Drive Lincolnshire, IL 60069, USA. PhoneImportant Safety Instructions NEC National Electrical CodeTable of Contents Setup Checklist Installation/Connections Overview Status LED flashes while the program is runningVentilation Monitor VentilationVentilation / Installation Overview Monitor/Integrator Box Wall Mounting SystemAUX Controller Connection and Placement IR Receiver & IR Bracket InstallationMini glossary Antenna HookupG E 1 Cable Service Hookup Connect cable service to the HD Integrator Box SystemRS-232C Control Connections Viewing Equipment Setup Connect Aux Control IR Output as required of your systemDVI Hookup to RJP or DVD Player Computer PC Hookup DVITV/Monitor RJP Connections TV/MonitorAudio Connection Digital Audio Optical Connections On-Screen Menus Overview Other Menus & On-Screen Displays InfoUser Remote Control Key Functions G E 2Mute Installer Remote Control Key FunctionsNumber Keypad Channel -/+Auto Program Channel Search Channel List Channel ListChannel Control OK Enter button Press the ADJ F or G button to adjustSignal being received Clock Setup On-Off Timers SetupTime Zone options for your local area Enter buttonUse the ADJ D E F G buttons to set the Daylight Savings See the nextUse the ADJ D or E button to highlight the Daylight Saving Use the ADJ D or E button to highlight Time Zone and pressUse the ADJ F or G button to select the Time Zone Press the OK Enter buttonMinutes and time period to turn-on You can set a time for the TV to automatically turn-onUse the ADJ D E F G buttons to choose AM / PM, Hours You can set a time for the TV to automatically turn-offG E 3 Use the ADJ D or E button to highlight Auto Off and pressUse the ADJ D or E button to choose On or Off Chip OK Enter buttonUse the ADJ D or E button to highlight Set Block Hour Enter the 4 digits passwordThis option sets up hour that you wish to block Use the ADJ D or E button to choose 1~12 hours and pressDescription of the TV FCC Rating Codes Use the ADJ D E F G buttons to choose and set up the menuOptions for Tvpg Rating Use the ADJ D or E button to highlight the Mpaa Rating Options for Mpaa RatingDescription of the Mpaa and TV FCC Rating Codes Rating and press the OK Enter button Enter the 4digits passwordUse the ADJ D or E button to highlight the Can. English Options for Can. English RatingCanadian French Ratings E Expect No restriction. G For all Use the ADJ D or E button to highlight the Can. FrenchOptions for Can. French Rating Use the ADJ D or E button to highlight the D/L Rating Will be available only for digital channel signalThis function operates only when TV has received Dim3 and press the OK Enter buttonTo highlight the Caption menu and press the OK Enter When finished, press Menu repeatedly to removeCaption Menu Press OK Enter buttonCustomize the digital captions that appear on your screen Use the ADJ D or E button to highlight Digital ModeUse the ADJ D or E button to choose Service 1-Service Use the ADJ D E F G buttons to customize each option FontUse the ADJ D / E buttons to choose Dolby Digital or PCM Sound MenuUse the ADJ D or E button to highlight Digital Output G E 4Use the ADJ D or E button to choose Mono, Stereo or SAP Use the ADJ D or E button to highlight Auto VolumeTo highlight the Sound menu and press the OK Enter Use the ADJ D or E button to choose English, Spanish or French and press the OK Enter buttonLanguage English, Español or Français Language ControlUse the ADJ D or E button to highlight and set the Menu Use the ADJ D or E button to highlight Menu LanguageSet ID Use the ADJ D or E button to choose 1-99 numbers and pressColor Temperature and press the OK Enter button Picture MenuFinished, press the Menu button Buttons to set your own settings for the options. WhenUse the ADJ D or E button to choose a preset screen Use the ADJ D or E button to choose Screen FormatUse the ADJ D or E button to choose Film Mode and press Use the ADJ D or E button to choose Noise ReductionTypical Installer Menu Commercial Mode Setup G E 5 Cloning Connections/Learning SetupTurn to the next page to continue Cloning Setup If batteries are removed, the Clone Clock time will be lostSet the Clock Optional Clone Programmer Learning SetupLearn Setup from Master TV/STB Disconnect TV/STB Power for 15 Seconds Cloning Connections / Teaching SetupTeach Master TV/STB’s Setup to the target Using the Installer’s Menu Installer MenuAccessing the Installer’s Menu Installer Menu Items 000 throughInstaller Menu Items 035 through Detailed Descriptions of Installer Menu Items Installer SequenceCaption Lock Mute DisableSleep Timer Poll RateAUX Status RJP AvailableStart Minor Channel Atsc Tune ModeAtsc Band VID OUT FormatFilm Mode Reference TV Features / Menus that can be ClonedChannel Picture Sound Setup Caption Changing/Adding Channel Labels on Master TV Adding Channel Icons and Labels in the 2-5-4 + Menu ModeTo Do Channel Editing/Labeling, proceed as follows Changing Source Labels on Master TVReference Detailed Information For Making a Master TV Detailed InstructionsProcedure to Check Software Version Reference Software Version CheckTV/STB Aux Input Configuration TV/STB Aux Input ConfigurationDisplays ‘No Signal’ message at Power Off TV/STB RS-232 Monitor Requirements / RS-232 TroubleshootingType of Connector D-Sub 9-Pin Female Communication Parameter Connecting the cableRS-232C Control Transmission / Receiving ProtocolMc Set ID DataCr Data Key code Refer to page A18 KeyCommand m cTo send IR remote key code Set ID OKDataxTroubleshooting Clone Programmer Troubleshooting Reference Cloning Procedure TroubleshootingReset Clone After Static Shock Troubleshooting Flow Chart Installer Quick Setup Guide G E 7Glossary of Terms OHM RF CableLG’S Responsibility For Customer Support/Service Please callCopyright 2008 LG Electronics U.S.A., Inc OWNER’S Responsibility