Speco Technologies DVR-16/IP user manual Motion Detect

Page 25

6.6.2.7 Any Key To Stop

When the event is triggered, the buzzer will beep, the Alarm Out relay will be activated. If you want to stop these actions by pressing any one key, then you must select “YES” for this item.

6.6.3 Motion Detect

This menu allows you to configure how Motion Detection works. Each camera can have its “Detect Area” and “Sensitivity” defined individually.

 

Motion Detect

 

1

Motion Detect

OFF

2

Configuration Table 2

 

3

Condition Set Up

 

4

Exit

 

 

 

 

6.6.3.1 Motion Detect

This item allows you to enable/ disable the motion detect function of the DVR-16/IP.

6.6.3.2 Configuration Table 2

Move the cursor to 2 Configuration Table 2 and press ENTER button, the table will appear. This table allows you to enable/ disable the day and night motion detect functions.

Alm In Type

Day: Alm In

Day: Motion

Night: Alm In

Night: Motion

Configuration Table 2

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

ESC For Return

6.6.3.3 Condition Set Up

This menu allows you to setup each camera’s motion detected area and sensitivity.

First select the wanted camera by using the right and left direction buttons, and then move the cursor to the second and third items to setup the chosen camera’s detect area and sensitivity.

6.6.3.4 Detect Area

This item allows you to setup the motion detect area of each camera. The screen is covered by 192 (16x12) “detection grids”.

You may use the DIRECTION buttons to move the cursor then press the ENTER button to enable/ disable the grids. Pressing MODE button can change the size of the cursor. You may also toggle all the grids on/off by pressing SET button (: disabled; : enabled).

 

 

Camera_1

1

Select

Camera 1

2

Detect Area

 

3Sensitivity

4Exit

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎ ◎

24

Image 25
Contents DVR-16/IP Precautions DVR-16/IP Menu Tree OSD Menu Setup ContentPage Windows Application Software DVR-16IP Remote Access of Video over the WebDVR-16/IP Application FeaturesQuick Installation Guide Buttons on the Front Panel Front Panel IntroductionSetup TimerPages ModeSET CD-RW DVR-16/IP Menu TreeEvent List OSD / Timer Monitor Camera Record Ntsc OSD/ Timer OSD Menu SetupEvent List Monitor Camera Covert Install1.3 PTZ RS-485 Baud RatePelco Speed Dome Termination Alarm REC PriorityGain Control REC PriorityCamera Detect RecordCamera Title Weekend 1 Day/ NightREC Event Only Switch REC While PBREC Event At HDD Full Alarm Rec Priority Mode1 Day/ Night Switch EventEvent Response Motion Detect Alarm Set/ Reset SW AlarmVideo Loss Detect Release TimeOthers Engineer Set Up Save/ Load DefaultCD-RW Copy Super MMX Mode Disable PasswordCovert Cam Visible Playback CheckExit Windows Application SoftwareConnect the USB Mobile Rack to PC Function Buttons Download the SoftwareGo to Begin PlaybackFast Rewind Rewind PlayingPreset Pt DVR-16IP Remote Access of Video over the WebButton Introduction Zoom In/ Zoom OutMenu/ Enter Direction buttonsStep Degree DVR-16/IP-related buttonsServer User Permission PasswordGeneral UserSystem Network settingsNetwork Video Dynamic DNS ConfigurationGET ID Password ConnectorsRear Board Channel ButtonsExternal I/O Board External I/O Port 37pin DsubRS-485 RJ11 SpecificationModel Name Appendix 1 Hard Disk Error Message Brand Capacity Rotation Speed Part Number Appendix 2 Supported HDDExample Appendix 3 RS-485 Command SetMMX Multiplexer-Matrix Appendix 4 Super MMX & Super MPX System SetupCamera ID Remark Super MPX Super Multiplexer Mode