Pioneer PDP-428XDA Watching TV Chapter, Turning the power on, Placing the system into standby

Page 20

06Watching TV

Chapter 6

Watching TV

Important

•Before watching broadcast channels, the built-in TV tuner must be set up. See Setting up TV channels automatically on page 27 for how to do this.

Turning the power on

•Press aon the plasma television when the POWER ON and STANDBY indicators are off.

•The system is on.

•The POWER ON indicator lights up blue.

•Press aor 0 to 9 on the remote control unit or STANDBY/ ON on the plasma television if the STANDBY indicator lights up red.

•The POWER ON indicator lights up blue.

•If you press 0 on the remote control unit, images from “INPUT 1” will be displayed.

•If you press 1 to 9, TV images will be displayed.

Placing the system into standby

•Press aon the remote control unit or STANDBY/ON on the plasma television.

•The STANDBY indicator lights up red.

•The system enters the standby mode and the image on the screen disappears.

Note

•When aon the plasma television is off, you cannot turn the power on by pressing aor 0 to 9 on the remote control unit or STANDBY/ON on the plasma television.

•If you are not going to use the plasma television for a long period of time, be sure to remove the power cord from the power outlet.

PDP-508XDA

POWER ON indicator

STANDBY indicator

ON STANDBY

button

PDP-428XDA

POWER ON indicator

STANDBY indicator

ON STANDBY

button

(Viewed from the underside of the display)

Plasma television status indicators

The table below shows the operational status of the plasma television. You can check the current status of the system with the indicators on the plasma television.

Indicator status		System status

POWER ON	STANDBY

		The power cord of the plasma television has been
		disconnected. Or, the power cord of the plasma
		television has been connected but the abutton
		of the plasma television is off.

		Power to the system is on

		The system is in the standby mode

For other than the above, see Troubleshooting on page 72.

20

En

Image 20

Contents Plasma Television Burning To use your plasma television for a long period of timeAfter-image lagging Operating Environment STANDBY/ON ButtonContents Using with other equipment Using the Hdmi ControlUsing Teletext Additional informationInstallation guidelines Important user informationImportant user information Chapter Usage guidelinesImportant user information To use this product for a long period of time Panel sticking and after-image lagAfter-image lagging due to remaining electrical load After-image lag image due to burningSafety precautions Safety precautions ChapterSide view Safety precautions Installation precautionsWhen using other items Supplied accessories Supplied accessories ChapterPart names Part names ChapterPlasma television Front STANDBY/ON button Input buttonPart names Plasma television Rear 15 16 17 18Part names Remote control unit Installing the plasma television PreparationPreparation Chapter Moving the plasma televisionMm to 18 mm Hook Cord Fitting Using a wall for stabilizationStabilizing on a table or rack Connecting the antenna Preparation Basic connectionsRouting cables Antenna cable commercially availablePreparing the remote control unit Connecting the power cordPreparation Inserting batteriesPreparation Operating range of the remote control unit 30ºTurning the power on Watching TVWatching TV Chapter Placing the system into standbyChanging channels Changing the volume and soundWatching TV Watching TV Switching the broadcast audio channel ModeWatching TV Using the multiscreen functions Press cto select the display modeSplitting the screen Screen Main screenPress dagain to cancel the function Watching TV Freezing imagesPress d Normal imageHome Menu Home Menu ChapterHome Menu overview For AV sourceHome Menu Using the Home Menu Press Home Menu to exit the menuUsing Auto Installation Setting upSetting up Chapter Setting up Setting Child LockReducing video noise Suppressing audio distortionSetting up Labeling TV channels Sorting preset TV channelsLanguage setting Repeat to enter up to five charactersSetting up AV Selection Basic picture adjustmentsFor AV source For PC sourceUsing Intelligent Mode Advanced picture adjustmentsUsing PureCinema ACL Using the Picture DetailUsing Colour Temp Using CTI and Colour Space Using Colour ManagementEliminating noise from images CTIComparing picture adjustments on the screen Using the 3DYC and I-P ModeMosquito NR 3DYCSetting up Sound adjustments Listening to audio from the sub screen using headphonesSound Effect SRS FocusPower Control No Signal off AV source onlyEnergy Save No Operation off AV source onlyPower Management PC source only Power ManagementWatching DTV programmes Viewing a channel banner i-PLATE Enjoying DTV broadcastsEnjoying DTV broadcasts Chapter Customizing channel related settings Enjoying DTV broadcastsViewing subtitles Registering channels in the Favourite ListReconfiguring the DTV channel settings Enjoying DTV broadcasts Activating the Favourites functionParental Control Parental Rating optionsEnjoying DTV broadcasts Quick Scan Auto ScanSelect Quick Scan / then Enter Select Auto Scan / then EnterManual Scan Clear All DataSelect Manual Scan / then Enter Select Clear All Data / then EnterTime Zone Setup Selecting a digital audio formatEnjoying DTV broadcasts Selecting an audio language Displaying technical informationScreen Saver Select the desired audio language / then EnterUseful adjustment settings Useful adjustment settings ChapterSwitching the vertical drive mode AV source only Adjusting image positions AV source onlySelecting a screen size manually Colour system settingSelecting a game mode Useful adjustment settings Selecting a screen size automaticallyDetecting side masks AV sourceItemDescription Room Light SensorBlue LED Dimmer Useful adjustment settings Orbiter Sleep Timer Using a passwordEntering a password Enter a correct four-digit password using buttons 0 toChanging the password Resetting the password functionIf you forget the password Enter the same password that you have entered in stepUsing with other equipment Using with other equipment ChapterConnecting a DVD player Connecting a set top boxVideo cable Audio/Video cable Game console/camcorder VCR playbackDisplaying an image from the game console or camcorder Connecting an amplifier/AV receiver Computer compatibility chartResolution Frequency Displaying an image from a personal computerVideo signals supported PC signals supportedHdmi Control supported Deep Colour supportedUsing with other equipment Connecting Hdmi equipmentSpecifying the type of input signals Activating the Input 3 Hdmi terminalUsing control cords Specifying the type of digital video signalsSpecifying the type of audio signals About SR+Connecting a USB device Readable memory cardsRemoving a USB device Readable data filesStarting the initial Home Gallery screen Starting a standard single-image screenSelecting a folder Starting a thumbnail screenStarting the Slide Show Setup screen Adjusting the picture qualitySelect Display Mode / Select Normal or Full / Select Playback Mode / Select Auto or Manual /Presetting manufacture codes Manufacture codesPress 0 to 9 to enter a three-digit manufacture code STBDVR VCRSTB set top box control buttons Colour RED/GREEN/YELLOW/BLUEDVD/DVR control buttons VCR control buttons RECIplay Starts playback VFF SrewUsing the Hdmi Control Using the Hdmi Control ChapterUsing the Hdmi Control functions Hdmi Control functionsConnecting an AV amp/DVD recorder/BD player Making the Hdmi Control connectionsAV amp Using the Hdmi ControlConnecting a DVD recorder Using the Hdmi Control Setting the Hdmi Control Using the Hdmi Control Using the Hdmi Control menus Hdmi Control menuUsing the Teletext functions Using TeletextUsing Teletext Chapter Using Teletext Operating the Teletext basics for DTVTroubleshooting Additional informationAdditional information Chapter GeneralCode Message Check Hdmi ControlOther Pin No Signal assignment Additional information Specifications TrademarksPioneer Corporation