Pioneer PDP 424MV specifications Rear View/ Terminal Board

Page 13

English

Rear View/ Terminal Board

Part Names and Function

6

AAC IN

Connect the included power cord here.

BEXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct polarity. Connect the(positive) speaker wire to the

EXT SPEAKER terminal and the (negative) speaker wire to the EXT SPEAKER terminal on both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

CVIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here. VIDEO1 can be used for Input or Output (see page 24).

DAUDIO1, AUDIO2, AUDIO3 These are audio input terminals.

The input is selectable. Set which video image to allot them from the SOUND menu screen.

ECOMPONENT1

Connect DVD’s, High Definition or Laser Discs, etc. here.

FPC2/COMPONENT2

PC2:	You can connect an analog RGB signal
	and the syncronization signal.

COMPONENT2: You can connect DVDs, High Definition sources, Laser Discs, etc. here.

This input can be set for use with an RGB or component source (see page 17).

GPC1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc. here. This input can be used for Input or Output (see page 24).

HPC3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a DVI output.

IRS-232C

Never connect any component to this connector without first consulting your Pioneer installation technician.

This connector is used for plasma display setup adjustments.

JREMOTE IN

Connect the remote cable* to the remote control’s remote jack to obtain wired remote control.

KREMOTE OUT

Connect the remote cable* to the REMOTE IN jack of the other display monitor to obtain wired remote control.

* The 1/8 Stereo Mini cable must be purchased separately.

En

Image 13

Contents PDP-424MV Operating Instructions Important Information PrecautionsRisk of Electric Shock Do not Open To avoid damage and prolong operating life Plasma monitor cleaning procedureRecommendations to avoid or minimize phosphor burn-in Declaration of Conformity Important Safety Instructions S021EF Contents Ventilation Requirements for enclosure mounting InstallationCreating a video wall Video signal PC/COMPONENT signalCable Management ClampBattery Installation and Replacement How to use the remote controlUsing the wired remote control mode Handling the remote controlReceives the signals from the remote control Turns the monitor’s power on and offPart Names and Function Front ViewRear View/ Terminal Board Remote Control Basic Operations Wide Operations When viewing videos or digital video discsWhen wide signals are input Screen Size Operation with Computer Signals Supported resolution Size screen 43 or Sxga Advanced menu mode Setting the language for the menus Language settings Menu OperationsMenu Tree Reset Restoring the factory default settings Adjusting the picture Picture Settings MenuSetting the color temperature Reducing noise in the pictureMaking the Low Tone adjustments Adjusting the color to the desired levelAdjusting the colors Changing the Gamma CurveScreen Settings Menu Sound Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, PHASE, ClockSetting the on-screen display Option1 Settings MenuSetting the PC2/COMPONENT2 connectors Checking the signal being transmitted to PC1 terminalSetting the Input Skip Setting high definition images to the suitable screen sizeResetting to the default values Input Skip settingsSetting the power management for computer images Option2 Settings MenuSTANDBY/ON indicator Setting the picture to suit the movie Orbiter Function settings Orbiter settings Inverse Settings Setting the time Soft Focus settings Setting the gray level for the Side Mask Side Mask settings Screen WiperSetting the screen size for S1/S2 video input Option3 Settings MenuSetting the signal and black level for DVI signal Using the timerEnabling/disabling the front panel controls Setting the power on modeLoop Out setting Enabling/disabling remote control wireless transmissionID number setting Video Wall setting Video Wall Position settings Divider settings DISP. Mode settings Auto ID settings ABL Link settings Screen settings P. on Delay settings ScreenColor System Settings Menu Advanced OSD Settings MenuSetting the menu mode Setting the video signal formatDVI-D 24-pin connector Digital Mini D-Sub 15-pin connector AnalogPin Assignments Supported resolution Table of Signals SupportedComputer input signals supported by this system English Symptom Checks Remedy TroubleshootingSignals Specifications