Pioneer PDP 424MV specifications Option1 Settings Menu, Setting the on-screen display

Page 24

Option1 Settings Menu

Setting the on-screen display

This sets the position of the menu, the display format (horizontal or vertical) etc.

Example: Turning the DISPLAY OSD off

On “OPTION1” menu, select “OSD”, then press the MENU/ SET button.

The “OSD” menu appears.

On “DISPLAY OSD” of “OSD” menu, select “OFF”.

 

 

 

OSD

 

 

 

DISPLAY OSD

 

 

:

OFF

 

OSD ADJUST

 

:

1

 

OSD ANGLE

 

:

H

 

OSD ORBITER

 

:

OFF

 

OSD CONTRAST

 

:

LOW

 

SEL.

ADJ.

EXIT RETURN

 

 

 

 

 

 

Information

DISPLAY OSD settings

ON: The informations on screen size, volume control, etc. will be shown.

OFF: The informations on screen size, volume control, etc. will not be shown.

The DISPLAY button on the remote control will not function either.

OSD ADJUST settings

Adjusts the position of the menu when it appears on the screen.

The position can be set between 1 to 6.

OSD ANGLE settings

Sets the display format (landscape “H” or portrait “V”). When the unit is installed vertically set the OSD ANGLE at “V”.

“H”

 

 

 

 

 

“V”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OPTION1

 

1 / 3

 

 

 

OPTION1

 

 

 

OSD

 

 

 

 

 

 

OSD

 

 

 

 

 

BNC INPUT

 

:

RGB

 

 

 

 

 

 

 

 

D-SUB INPUT

:

RGB

 

 

BNC INPUT

 

 

 

 

RGB SELECT

:

AUTO

 

 

:

RGB

 

 

 

HD SELECT

 

:

1080B

 

 

D-SUB INPUT

 

 

 

INPUT SKIP

 

:

OFF

 

 

:

RGB

 

 

 

ALL RESET

 

:

OFF

 

 

RGB SELECT

 

 

 

NEXT PAGE

 

 

 

 

:

AUTO

 

 

 

SEL.

MENU OK

EXIT RETURN

 

 

HD SELECT

 

 

 

 

 

 

 

 

 

 

 

:

1080B

 

 

 

 

 

 

 

 

 

 

INPUT SKIP

 

 

 

 

 

 

 

 

 

 

 

:

OFF

 

 

 

 

 

 

 

 

 

 

ALL RESET

 

 

 

 

 

 

 

 

 

 

 

:

OFF

 

 

 

 

 

 

 

 

 

 

 

 

1024

768

 

 

 

 

 

 

 

 

 

SEL. MENU OK

 

 

 

 

 

 

 

 

 

 

 

 

EXIT RETURN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OSD ORBITER settings

ON: The position of the menu will be shifted by eight dots each time OSD is displayed.

OFF: OSD will be displayed at the same position.

OSD CONTRAST settings NORMAL: OSD brightness is set to normal. LOW: OSD brightness is set to lower.

Setting the PC2/COMPONENT2 connectors

Select whether to set the input of the PC2/COMPONENT2 to RGB and component.

Example: Set the BNC INPUT mode to “COMP.”

On “BNC INPUT” of “OPTION1” menu, select “COMP.”.

 

 

 

OPTION1

 

1 / 3

 

OSD

 

 

 

 

BNC INPUT

 

 

:

COMP.

 

D-SUB INPUT

 

:

RGB

 

RGB SELECT

 

:

AUTO

 

HD SELECT

 

:

1080B

 

INPUT SKIP

 

:

OFF

 

ALL RESET

 

:

OFF

 

NEXT PAGE

 

 

 

 

SEL.

ADJ.

EXIT RETURN

 

 

 

 

 

 

Information

BNC INPUT Settings

RGB: Use the 5BNC terminals for HD, VD and RGB signals.

COMP.: Use the 3BNC terminals for component signals.

Checking the signal being transmitted to PC1 terminal

Use this to confirm the signal being transmitted to the PC1 terminal.

It is set to RGB and can not be adjusted.

 

 

OPTION1

 

1 / 3

 

OSD

 

 

 

BNC INPUT

:

RGB

 

D-SUB INPUT

 

:

RGB

 

RGB SELECT

:

AUTO

 

HD SELECT

:

1080B

 

INPUT SKIP

:

OFF

 

ALL RESET

:

OFF

 

NEXT PAGE

 

 

 

CAN NOT ADJUST

 

 

 

 

 

 

 

Setting a computer image to the correct RGB select screen

With the computer image, select the RGB Select mode for a moving image such as (video) mode, wide mode or digital broadcast.

Example: Setting the “RGB SELECT” mode to “MOTION ”

On “RGB SELECT” of “OPTION1” menu, select “MOTION”.

 

 

 

OPTION1

 

1 / 3

 

OSD

 

 

 

 

BNC INPUT

 

:

RGB

 

D-SUB INPUT

 

:

RGB

 

RGB SELECT

 

 

:

MOTION

 

HD SELECT

 

 

1024⋅768

 

INPUT SKIP

 

:

OFF

 

ALL RESET

 

:

OFF

 

NEXT PAGE

 

 

 

 

SEL.

ADJ.

EXIT RETURN

 

 

 

 

 

 

Information

RGB SELECT modes

One of these 8 modes must be selected in order to display the following signals correctly.

AUTO: Select the suitable mode for the specifications of input signals as listed in the table “Computer input signals supported by this system” on page 29.

STILL: To display VESA standard signals. (Use this mode for a still image from a computer.)

MOTION: The video signal (from a scan converter) will be converted to RGB signals to make the picture more easily viewable. (Use this mode for a motion image from a computer.)

English

OSD (On Screen Display) Controls

17

En

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PDP-424MV Operating Instructions Precautions Important InformationRisk of Electric Shock Do not Open Plasma monitor cleaning procedure To avoid damage and prolong operating lifeRecommendations to avoid or minimize phosphor burn-in Declaration of Conformity Important Safety Instructions S021EF Contents Installation Ventilation Requirements for enclosure mountingVideo signal PC/COMPONENT signal Creating a video wallCable Management ClampHow to use the remote control Battery Installation and ReplacementUsing the wired remote control mode Handling the remote controlTurns the monitor’s power on and off Receives the signals from the remote controlPart Names and Function Front ViewRear View/ Terminal Board Remote Control Basic Operations When viewing videos or digital video discs Wide OperationsScreen Size Operation with Computer Signals When wide signals are input Supported resolution Size screen 43 or SxgaSetting the language for the menus  Advanced menu mode Language settings Menu OperationsReset Menu Tree Restoring the factory default settings Picture Settings Menu Adjusting the picture Setting the color temperature Reducing noise in the pictureAdjusting the color to the desired level Making the Low Tone adjustmentsAdjusting the colors Changing the Gamma CurveSound Settings Menu Screen Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, PHASE, ClockOption1 Settings Menu Setting the on-screen displaySetting the PC2/COMPONENT2 connectors Checking the signal being transmitted to PC1 terminalSetting high definition images to the suitable screen size Setting the Input SkipResetting to the default values  Input Skip settingsOption2 Settings Menu Setting the power management for computer imagesSTANDBY/ON indicator Setting the picture to suit the movie Orbiter settings  Orbiter Function settings Inverse Settings  Setting the timeSetting the gray level for the Side Mask  Soft Focus settings Side Mask settings Screen WiperOption3 Settings Menu Setting the screen size for S1/S2 video inputSetting the signal and black level for DVI signal Using the timerSetting the power on mode Enabling/disabling the front panel controlsEnabling/disabling remote control wireless transmission Loop Out settingID number setting Video Wall setting Divider settings  Video Wall Position settings DISP. Mode settings  Auto ID settings Screen settings  ABL Link settings P. on Delay settings ScreenAdvanced OSD Settings Menu Color System Settings MenuSetting the menu mode Setting the video signal formatMini D-Sub 15-pin connector Analog DVI-D 24-pin connector DigitalPin Assignments Table of Signals Supported Supported resolutionComputer input signals supported by this system English Troubleshooting Symptom Checks RemedySpecifications Signals
Top Page Image Contents