Harman 4800, 4820 user manual Use, Press and hold the RTA/LOAD button to load the preset

Page 42

Section 5

 

 

 

 

DriveRack

 

 

 

®

 

 

In Use

 

 

Under normal operation the most common modes are Configuration, Edit, Store and Recall Preset. The simplest way to illustrate these modes in use is by example; this will be done for both the Front Panel Navigation as well as the GUI.

In our example we’ll create a Stereo Tri-Amped System with a Mono Sub, a mono send to Delayed House speakers, and Side Fill sends.

5.1 - Front Panel Operation

The example begins with recalling a preset from the Preset Table:

1. Press the PRESET/RECALL button to return to the main preset screen.

2.Press and hold the PRESET/RECALL button to enter Preset Recall mode.

3.Select Preset 8 Stereo 2-Way with Sub from the preset table by turning the Encoder #1 knob until Preset 8 appears on the display.

4.Press and hold the RTA/LOAD button to load the preset.

This 2x5 preset is a good starting point, but we want to make some modifications to it. We want to link the Input Graphic EQs and change the Inserts on the main stereo feed from Notch Filters to Compressors. We also want to rename the Inputs, put a Mixer in the Mid position, and lengthen the Delay that feeds Output 6, our Delayed speaker send. To do all this we must make a Configuration change.

To make a Configuration change:

1.Since the preset was just recalled, we’re already in Edit Preset mode and can press and hold the WIZARD/CONFIG button for two seconds to enter Configuration mode.

32

 

DriveRack® 4800/4820 User Manual

 

 

Image 42
Contents 4800/4820 Importantsafetyinstructions Important Safety Instructions Table of Contents DriveRackDriveRack DriveRack Features DriveRack 4800/4820 Features IntroductionDriveRackDriveRackIntroduction Service Contact Info WarrantyIntroductionDriveRack Front panel Getting Started Rear Panel 4800/4820 Getting Started Front PanelThreshold Meters Input Channel Select A-DOuput Channel Select RTA Input JackGettingStarted System Architect Features System Architect Control SoftwareMute Buttons Installation Minimum System Requirements for System Architect areRecommended System Requirements DriveRack Attributes DriveRack Philosophy DriveRack 4800/4820 Philosophy AttributesNavigation Front Panel Operation NavigationModes of Operation Return to Edit mode by pressing the Preset button DriveRack While in Edit mode press and hold the UTILITY/METER button DriveRack DriveRack Module view System Architect DriveRack 4800/4820 Philosophy Software Operation DriveRack PhilosophySystemArchitectDriveRack4800/4820FileStorage Module ViewSoftware Operation Device WindowDevice Edit Menu Device View FeaturesDevice File Menu Device Tools MenuPreset Tool Device View MenuDevice Help Menu Meters Mutes and SolosVenue View Venue File MenuSoftwareGUI SoftwareOp rationOverview Venue View MenuVenue Insert Menu Venue Panel Menu Venue Tools MenuVenue Window Menu Venue Help MenuDriveRack Front panel Press and hold the RTA/LOAD button to load the preset UseDriveRack Store the name by pressing the STORE/DELETE button DriveRack GUI Operation DriveRack DriveRack Detailed Detailed Parameters Input MixerSelected Source Switch Detailed Parameters Input RouterFrequency switch EQ On/Off switchFlat/Restore switch Detailed Parameters Input Graphic EQDetailed Parameters Input 9-Band Parametric EQ Delay fader Detailed Parameters Input DelayDelay On/Off switch Units switchMaster Mute switch Detailed Parameters Output MixerChannels A-D Detailed Parameters Output Router Detailed Parameters OutputBandpassFilter/Crossover Detailed Parameters Output 6-Band Parametric EQ Detailed Parameters Output Delay AFS On/Off switch Mode switchClear Live and Clear All buttons Detector Highpass fader Type switchLive Filter Lift switch Sensitivity faderThreshold fader AGC On/Off switchDetailed Parameters Automatic Gain Control AGC Insert Target faderAttack fader Limiter Auto On/Off switchWindow fader Release faderAutoWarmth On/Off switch Detailed Parameters AutoWarmth InsertAmount fader OverEasy fader Compressor On/Off switchDetailed Parameters Compressor Insert Ratio faderAuto On/Off switch Hold faderFrequency fader De-Esser On/Off switchDetailed Parameters De-EsserInsert Width faderGate On/Off switch Detailed Parameters Noise GateMax Attenuation fader Detailed Parameters Limiter Insert Limiter On/Off switchPeakStopPlus On/Off switch PeakStopPlus Overshoot faderDetailed Parameters Notch On/Off switch Detailed Parameters Notch Filter InsertSubHarmonic Level fader SubHarmonic Synth On/Off switchDetailed Parameters SubHarmonic Synthesizer Insert 24-36Hz Level faderUtilities Gains & Trims UtilitiesMiscellaneous Sample RateUtilities Real Time Clock Access RightsPreset Range UsersDriveRack DriveRackAppendix Specifications AppendixDriveRackDriveRackAppendix Block Diagram Preset Table Crossover TableDigital I/O and Clocking Word Clock Termination ZoneControllerWiringandInstallation Zone Controller WiringZone Controller Installation AppendixDriveRack GND ZC-4 Wiring Diagram Power-Up Button Functions Factory ResetFactory Reset Information Hard Factory ResetIP address Ethernet NetworkingOverview of TCP/IP Basics SubnetConnecting the Computer Directly to the DriveRack Dhcp Dynamic Host Configuration ProtocolAssumptions Setup of a Simple Isolated Ethernet Network Using Dhcp ProxyVirtual Private Networks VPN Network Considerations and LimitationsNetworkTroubleshooting Software FirewallEthernet Link Copyrights AppendixDriveRack DriveRackAppendix 18-0353-B