Panasonic TH-103PF10EK manual Important Safety Notice, Important the Moulded Plug

Page 3

Important Safety Notice

WARNING

1)To prevent damage which may result in fire or shock hazard, do not expose this appliance to dripping or splashing.

Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.)

No naked flame sources, such as lighted candles, should be placed on / above the set.

2)To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel.

3)Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type power plug. This plug will only fit an earthing-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician.

Do not defeat the purpose of the earthing plug.

4)To prevent electric shock, ensure the earthing pin on the AC cord power plug is securely connected.

CAUTION

This appliance is intended for use in environments which are relatively free of electromagnetic fields.

Using this appliance near sources of strong electromagnetic fields or where electrical noise may overlap with the input signals could cause the picture and sound to wobble or cause interference such as noise to appear.

To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic fields.

IMPORTANT: THE MOULDED PLUG

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Shall the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark ASA or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained.

A replacement fuse cover can be purchased from your local Panasonic Dealer.

If the fitted moulded plug is unsuitable for the socket outlet in your home, then the fuse shall be removed and the plug cut off and disposed of safety. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below.

If in any doubt, please consult a qualified electrician.

WARNING : — THIS APPARATUS MUST BE EARTHED.

IMPORTANT : —The wires in this mains lead are coloured in accordance with the following code: —

Green-and-Yellow : Earth

Blue: Neutral Brown: Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse. Open the fuse compartment with a screwdriver and replace the fuse.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents English High Definition Plasma DisplayOperating Instructions Model No. TH-103PF10EKTable of Contents Important the Moulded Plug Important Safety NoticeTransport only in upright position Safety PrecautionsSetup Do not place any objects on top of the Plasma DisplaySafety Precautions When using the Plasma DisplayIf problems occur during use Take steps to prevent toppling Clean the power cable regularly to prevent it becoming dustyAccessories Accessories SupplyRemote Control Batteries Open ConnectionsAudio OUT Terminals connection AC cord fixing CloseSignal Names for Mini D-sub 15P Connector PC Input Terminals connectionConnections Basic format for control data CommandSerial Terminals connection Communication parametersComponent / RGB connection DVI-D Input Connector Pin LayoutsSignal Name DVI-D connectionRight side surface Power On / OffConnecting the AC cord plug to the Plasma Display Connecting the plug to the Wall OutletSelecting the input signal Initial selectionsSelecting the On-Screen Menu Language Basic Controls Basic Controls See page 23 On-Screen Menu DisplaysOn-Screen Menu Displays SignalAspect Controls Normalisation Adjusting Pos. /SizeAdjusting Pos. /Size Multi PIP Options Advanced PIPCinema Picture AdjustmentsNormal DynamicPicture Adjustments Advanced settingsSound Adjustment On Off Sound AdjustmentSDI Sound Output MuteSelect the magnification required for the enlarged display Digital ZoomDisplay the operation guide Select the area of the image to be enlargedPresent Time Setup Present Time Setup / Set up TimerPresent Time Setup / Set up Timer Set up TimerReversal / Scroll selection Mode selectionStart setting Screensaver For preventing image retentionSetup of Screensaver Time Reduces screen image retentionScreensaver For preventing image retention Side Panel Adjustment Reduces power consumption Customizing the Input labelsAddition sign Selected Input How to Setup Multi Display Setup for Multi DisplayDisplay Number locations for each arrangement Examples Setup for Multi DisplayAI-synchronization ID Remote Control FunctionID remote control button operation ID CancellationHow to setup Portrait Set up for PortraitViewing Area / Location Set up for PortraitSetup for Input Signals Component / RGB-in select3D Y/C Filter For Ntsc AV images NR / Block NR / Mosquito NR Setup for Input SignalsCinema reality Colour system / Panasonic AutoDisplays the H Horizontal / V Vertical frequencies Setting RGB sync signalSync Freq. kHz / V-Freq. HzEffect Adjustments Options AdjustmentsOptions Adjustments On Sets the colour temperature for TV studio Off-timerInitial Power Off Nullify all the settings adjustedNormalization Weekly Command Timer Weekly Command TimerPress to select Time / Command Shipping condition Plasma Display panel TroubleshootingDVI-D DVI-D/COMPONENT/RGB/PC input signalsCommand list of Weekly Command Timer Specifications Memo Memo For business users in the European Union Customer’s RecordSales and Support Information Customer Care Centre
Top Page Image Contents