Sharp PGLW2000 appendix Inserting the Batteries, Usable Range, Remote control signal transmitters

Page 15

Inserting the Batteries

1 Pull down the tab on the cover and remove the cover towards the direction of the arrow.

2 Insert the batteries.

• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment.

3 Insert the lower tab of the cover into the opening, and lower the cover until it clicks in place.

Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below

Caution

Danger of explosion if battery is incorrectly replaced. Replace only with alkaline or manganese batteries.

Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment.

Batteries of different types have different properties, therefore do not mix batteries of different types.

Do not mix new and old batteries.

This may shorten the life of new batteries or may cause old batteries to leak.

Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak. Battery fl uid from leaked batteries is harmful to skin, therefore ensure you wipe them fi rst and then remove them using a cloth.

The batteries included with this projector may run down in a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries.

Remove the batteries from the remote control if you will not be using the remote control for a long time.

Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

Usable Range

Remote control sensor

 

The remote control can be used to control the

 

projector within the ranges shown in the

 

illustration.

 

Note

 

• The signal from the remote control can be

30°

refl ected off a screen for easy operation.

 

However, the effective distance of the signal

 

may differ depending on the screen material.

 

Introduction

When using the remote control

Ensure that you do not drop it or expose it to moisture or high temperature.

The remote control may malfunction under a fl uorescent lamp. In this case, move the projector away from the fl uorescent lamp.

30°

33 n (10 m)

Remote control signal transmitters

Remote control

13

Image 15
Contents PG-LW2000 Model No Serial No Void the users authority to operate this equipment See bottom of projectorInformation Product Disposal Optional accessories AccessoriesContents Viewing Stereoscopic 3D Images ReferencePower-Cord Protection CleaningPower Sources AccessoriesOverloading Damage Requiring ServiceReplacement Parts Safety CheckAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment 15 16 Part Names and FunctionsRear View Terminals Part Names and Functions Remote control signal transmitters Inserting the BatteriesUsable Range Easy Start Setup and ProjectionCorrecting trapezoidal distortion using Keystone Correction On the remote controlInput list Standard Setup Front Projection Setting Up the ProjectorVideo Setup Setting Up the ProjectorSignal Input Normal Mode Screen Size and Projection DistanceScreen Lens center Ceiling-Mount Setup Projection PRJ ModeYou may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment AC socket To AC outlet Power cord supplied Connecting the Power CordControlling the Projector by a Computer RS-232C Terminal D-sub 9 pin male connectorPower indicator Lamp indicator Turning the Projector On/OffTurning the Projector On Image Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Press Enter to exit the Setup Guide screenRotate the zoom ring to enlarge or shrink the picture size Adjusting the HeightAdjusting the Picture Size Use the rear adjustment foot to make the projector levelPress Keystone Correcting Trapezoidal DistortionSwitching the Input Mode Adjusting the VolumeVOL +/- Volume buttons Input buttons AV Mute button Buttons Resize Mode Press ResizeButton About Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot FunctionDisplaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImagePicture menu Menu ItemsMain menu Projector adjustment PRJ-ADJ1/2 menu Example Using the Menu ScreenMenu Selections Quick Start Menu Press MenuFollowing items can be configured on the Quick Start Menu Example Adjusting BrightQuick Start Menu Menu Selections Complete MenuPress Enter To adjust the projected image while watching itPress P or R and select Bright to adjust Press O or Q to adjust the item selectedPicture Adjustment Picture Menu Selecting the Picture ModeMenu operation n Adjusting Hue, Saturation, or Value Adjusting the ImageAdjusting the Color Temperature Adjusting the ColorsSelecting the Film Mode Eco+QuietReducing Image Noise DNR Signal Adjustment SIG-ADJ Menu Resolution SettingSignal Type Setting When reproducing Ntsc signals in PAL video equipment Setting the Video SystemSetting the Video Setup Checking the Input SignalKeystone Correction Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Adjusting the Image PositionFor Americas only Setting the OverscanSetting the On-screen Display Closed CaptionSelecting the Wall Color Selecting the Setup GuideSelecting the Background Image Reversing/Inverting Projected ImagesFan Mode Setting Auto Sync Auto Sync AdjustmentAuto Power Off Function Speaker SettingEnter the same keycode in Re- confirm To cancel the keycode that you have already setWhen the System Lock is set System Lock FunctionSelect On, then press Enter Adjusting the Projector Function PRJ-ADJ1/2 MenuKeylock Function Taking the Keylock OffSelecting the Quick Start Menu Setting the Function Button OperationStandby Mode Returning to the Default SettingsViewing Stereoscopic 3D Images Precautions on Viewing Stereoscopic 3D ImagesShutter glasses control light signal Information on the 3D Projection FunctionAppendix Using 3D Viewing Mode Projecting 3D imagesEnding 3D projection Cleaning the projector MaintenanceAbout the temperature warning indicator Maintenance IndicatorsAbnormally high Are high Lower than 95F +35ºC Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Remove the lamp unit coverSTANDBY/ON button AC socket Resetting the Lamp Timer Basic format RS-232C Specifications and CommandsComputer control Communication conditionsComputer Projector CommandsRGB PAL CC1 Computer Compatibility ChartDTV 19-22 Troubleshooting53, 54 Problem Check Sharp Electronics France For Sharp AssistanceSpecifications Units inches mm DimensionsIndex
Related manuals
Manual 75 pages 34.96 Kb