Sharp PGLW2000 Overloading, Object and Liquid Entry, Servicing, Damage Requiring Service, Heat

Page 9

15. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fi re or electric shock.

16. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fi re or electric shock. Never spill liquid of any kind on the product.

17.Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualifi ed service personnel.

18.Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualifi ed service personnel under the following conditions:

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the product.

c.If the product has been exposed to rain or water.

d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualifi ed technician to restore the product to normal operation.

e.If the product has been dropped or damaged in any way.

f.When the product exhibits a distinct change in performance, this indicates a need for service.

19. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specifi ed by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in

re, electric shock, or other hazards.

20.Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21.Wall or Ceiling Mounting

This product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22.Heat

This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifi ers) that produce heat.

Introduction

DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM and DLP® LinkTM are trademarks of Texas Instruments.

PC/AT is a registered trademark of International Business Machines Corporation in the United States.

Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.

HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

All other company or product names are trademarks or registered trademarks of their respective companies.

Some IC chips in this product include confi dential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.

7

Image 9
Contents PG-LW2000 Model No Serial No Void the users authority to operate this equipment See bottom of projectorInformation Product Disposal Optional accessories AccessoriesContents Viewing Stereoscopic 3D Images ReferencePower Sources CleaningAccessories Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment 15 16 Part Names and FunctionsRear View Terminals Part Names and Functions Remote control signal transmitters Inserting the BatteriesUsable Range Easy Start Setup and ProjectionCorrecting trapezoidal distortion using Keystone Correction On the remote controlInput list Video Setup Setting Up the ProjectorSetting Up the Projector Standard Setup Front ProjectionSignal Input Normal Mode Screen Size and Projection DistanceScreen Lens center Ceiling-Mount Setup Projection PRJ ModeYou may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment AC socket To AC outlet Power cord supplied Connecting the Power CordControlling the Projector by a Computer RS-232C Terminal D-sub 9 pin male connectorPower indicator Lamp indicator Turning the Projector On/OffTurning the Projector On Adjusting the Projected Image Adjusting the Focus About the Setup GuidePress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Picture Size Adjusting the HeightUse the rear adjustment foot to make the projector level Rotate the zoom ring to enlarge or shrink the picture sizePress Keystone Correcting Trapezoidal DistortionSwitching the Input Mode Adjusting the VolumeVOL +/- Volume buttons Input buttons AV Mute button Buttons Resize Mode Press ResizeButton About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImagePicture menu Menu ItemsMain menu Projector adjustment PRJ-ADJ1/2 menu Menu Selections Quick Start Menu Using the Menu ScreenPress Menu ExampleQuick Start Menu Example Adjusting BrightMenu Selections Complete Menu Following items can be configured on the Quick Start MenuPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press EnterPicture Adjustment Picture Menu Selecting the Picture ModeMenu operation n Adjusting the Color Temperature Adjusting the ImageAdjusting the Colors Adjusting Hue, Saturation, or ValueSelecting the Film Mode Eco+QuietReducing Image Noise DNR Signal Adjustment SIG-ADJ Menu Resolution SettingSignal Type Setting Setting the Video Setup Setting the Video SystemChecking the Input Signal When reproducing Ntsc signals in PAL video equipmentSetting the Resize Mode Adjusting the Projected Image SCR-ADJ MenuAdjusting the Image Position Keystone CorrectionSetting the On-screen Display Setting the OverscanClosed Caption For Americas onlySelecting the Background Image Selecting the Setup GuideReversing/Inverting Projected Images Selecting the Wall ColorAuto Power Off Function Auto Sync Auto Sync AdjustmentSpeaker Setting Fan Mode SettingWhen the System Lock is set To cancel the keycode that you have already setSystem Lock Function Enter the same keycode in Re- confirmKeylock Function Adjusting the Projector Function PRJ-ADJ1/2 MenuTaking the Keylock Off Select On, then press EnterStandby Mode Setting the Function Button OperationReturning to the Default Settings Selecting the Quick Start MenuViewing Stereoscopic 3D Images Precautions on Viewing Stereoscopic 3D ImagesShutter glasses control light signal Information on the 3D Projection FunctionAppendix Using 3D Viewing Mode Projecting 3D imagesEnding 3D projection Cleaning the projector MaintenanceAbout the temperature warning indicator Maintenance IndicatorsAbnormally high Are high Lower than 95F +35ºC Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Remove the lamp unit coverSTANDBY/ON button AC socket Resetting the Lamp Timer Computer control RS-232C Specifications and CommandsCommunication conditions Basic formatComputer Projector CommandsRGB PAL CC1 Computer Compatibility ChartDTV 19-22 Troubleshooting53, 54 Problem Check Sharp Electronics France For Sharp AssistanceSpecifications Units inches mm DimensionsIndex
Related manuals
Manual 75 pages 34.96 Kb