Sharp PG-LW2000, PGLW2000 appendix Information Product Disposal

Page 4
U.S.A. ONLY
U.S.A. ONLY

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

PRODUCT DISPOSAL

This product utilizes lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at 1-800-BE-SHARP.

Caution Concerning Lamp Replacement

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.

Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Caution

Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury.

Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

Do not touch the glass surface of the lamp unit or the inside of the projector.

Do not loosen other screws except for the lamp unit cover and lamp unit.

Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

Carefully change the lamp by following the instructions described on pages 56 to 58.

* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.

*If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center for repair.

2

Image 4
Contents PG-LW2000 Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Accessories Optional accessoriesContents Reference Viewing Stereoscopic 3D ImagesCleaning Power SourcesAccessories Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Part Names and Functions 15 16Rear View Terminals Part Names and Functions Inserting the Batteries Remote control signal transmittersUsable Range Setup and Projection Easy StartOn the remote control Correcting trapezoidal distortion using Keystone CorrectionInput list Setting Up the Projector Video SetupSetting Up the Projector Standard Setup Front ProjectionScreen Size and Projection Distance Signal Input Normal ModeScreen Lens center Projection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment You may need other cables or connectors not listed belowConnecting the Projector to Other Equipment Connecting the Power Cord AC socket To AC outlet Power cord suppliedRS-232C Terminal D-sub 9 pin male connector Controlling the Projector by a ComputerTurning the Projector On/Off Power indicator Lamp indicatorTurning the Projector On About the Setup Guide Adjusting the Projected Image Adjusting the FocusPress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Height Adjusting the Picture SizeUse the rear adjustment foot to make the projector level Rotate the zoom ring to enlarge or shrink the picture sizeCorrecting Trapezoidal Distortion Press KeystoneAdjusting the Volume Switching the Input ModeVOL +/- Volume buttons Input buttons AV Mute button Buttons Press Resize Resize ModeButton About Copyrights Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreezing a Moving Image Displaying an Enlarged Portion of an ImageMenu Items Picture menuMain menu Projector adjustment PRJ-ADJ1/2 menu Using the Menu Screen Menu Selections Quick Start MenuPress Menu ExampleExample Adjusting Bright Quick Start MenuMenu Selections Complete Menu Following items can be configured on the Quick Start MenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press EnterSelecting the Picture Mode Picture Adjustment Picture MenuMenu operation n Adjusting the Image Adjusting the Color TemperatureAdjusting the Colors Adjusting Hue, Saturation, or ValueEco+Quiet Selecting the Film ModeReducing Image Noise DNR Resolution Setting Signal Adjustment SIG-ADJ MenuSignal Type Setting Setting the Video System Setting the Video SetupChecking the Input Signal When reproducing Ntsc signals in PAL video equipmentAdjusting the Projected Image SCR-ADJ Menu Setting the Resize ModeAdjusting the Image Position Keystone CorrectionSetting the Overscan Setting the On-screen DisplayClosed Caption For Americas onlySelecting the Setup Guide Selecting the Background ImageReversing/Inverting Projected Images Selecting the Wall ColorAuto Sync Auto Sync Adjustment Auto Power Off FunctionSpeaker Setting Fan Mode SettingTo cancel the keycode that you have already set When the System Lock is setSystem Lock Function Enter the same keycode in Re- confirmAdjusting the Projector Function PRJ-ADJ1/2 Menu Keylock FunctionTaking the Keylock Off Select On, then press EnterSetting the Function Button Operation Standby ModeReturning to the Default Settings Selecting the Quick Start MenuPrecautions on Viewing Stereoscopic 3D Images Viewing Stereoscopic 3D ImagesInformation on the 3D Projection Function Shutter glasses control light signalAppendix Projecting 3D images Using 3D Viewing ModeEnding 3D projection Maintenance Cleaning the projectorMaintenance Indicators About the temperature warning indicatorAbnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitSTANDBY/ON button AC socket Resetting the Lamp Timer RS-232C Specifications and Commands Computer controlCommunication conditions Basic formatCommands Computer ProjectorRGB PAL CC1 Compatibility Chart ComputerDTV Troubleshooting 19-2253, 54 Problem Check For Sharp Assistance Sharp Electronics FranceSpecifications Dimensions Units inches mmIndex
Related manuals
Manual 75 pages 34.96 Kb