Sharp PG-LW2000, PGLW2000 appendix Precautions on Viewing Stereoscopic 3D Images

Page 52

Viewing Stereoscopic 3D Images

Precautions on Viewing Stereoscopic 3D Images

Before viewing stereoscopic 3D images, please read this section carefully.

WARNING

Under normal conditions, viewing stereoscopic 3D images is safe for any duration that you would normally view your screen. However, some people may experience discomfort. The following precautions are recommended to minimize the potential for experiencing visual problems or any adverse symptoms.

Take regular breaks, at least 5 to 15 minutes after every 30 to 60 minutes of stereoscopic 3D viewing.

* Based on the guidelines issued by the 3D Consortium revised December 10, 2008.

Maintain an appropriate distance from the screen. Viewing from too close a distance can strain your eyes. If you experience eye strain, immediately discontinue viewing.

If you experience any of the following symptoms during viewing:

• nausea, queasiness/dizziness, headache, blurry vision or double vision that lasts longer than few seconds

Do not engage in any potentially hazardous activity (for example, driving a vehicle) until your symptoms have completely gone away. If symptoms persist, discontinue use and do not resume

stereoscopic 3D viewing without discussing your symptoms with a physician.

As you get more comfortable viewing stereoscopic 3D:

Adjust the parallax on the 3D-video playback equipment. (You may not be able to adjust the parallax on some models of equipment.)

Adjust the projected image to the most comfortable viewing size by zooming.

(Projecting images on the smallest or largest screen size possible may eliminate the stereoscopic effect and strain your eyes.)

Use the DLP® Link™ Invert function to properly set the video for your left and right eyes. (For

details on using “DLP® Link™ Invert”, see the section on its operation in this operation manual.)

The following people should limit stereoscopic 3D viewing:

Children under 6 years of age (to protect the eye growth process)

People with a history of photosensitivity

People with heart disease

People in poor health

People who are sleep deprived

People who are physically tired

People under the influence of drugs or alcohol

Epilepsy

A small percentage of the population may experience epileptic seizures when viewing certain types of images that contain flashing patterns of light.

IF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY

The following people should consult a physician before viewing stereoscopic 3D images.

Anyone with a history of epilepsy, or who has a family member with a history of epilepsy

Children under 6 years of age

Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by flashing light effects

SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF EPILEPSY

Discontinue use if you experience any of the following symptoms while viewing stereoscopic 3D images.

Involuntary movements, eye or muscle twitching

Muscle cramps

Nausea, dizziness, or queasiness

Convulsions

Disorientation, confusion, or loss of awareness of your surroundings

50

Image 52
Contents PG-LW2000 Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Accessories Optional accessoriesContents Reference Viewing Stereoscopic 3D ImagesCleaning Power SourcesAccessories Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Part Names and Functions 15 16Rear View Terminals Part Names and Functions Inserting the Batteries Remote control signal transmittersUsable Range Setup and Projection Easy StartOn the remote control Correcting trapezoidal distortion using Keystone CorrectionInput list Setting Up the Projector Video SetupSetting Up the Projector Standard Setup Front ProjectionScreen Size and Projection Distance Signal Input Normal ModeScreen Lens center Projection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment You may need other cables or connectors not listed belowConnecting the Projector to Other Equipment Connecting the Power Cord AC socket To AC outlet Power cord suppliedRS-232C Terminal D-sub 9 pin male connector Controlling the Projector by a ComputerTurning the Projector On/Off Power indicator Lamp indicatorTurning the Projector On About the Setup Guide Adjusting the Projected Image Adjusting the FocusPress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Height Adjusting the Picture SizeUse the rear adjustment foot to make the projector level Rotate the zoom ring to enlarge or shrink the picture sizeCorrecting Trapezoidal Distortion Press KeystoneAdjusting the Volume Switching the Input ModeVOL +/- Volume buttons Input buttons AV Mute button Buttons Press Resize Resize ModeButton About Copyrights Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreezing a Moving Image Displaying an Enlarged Portion of an ImageMenu Items Picture menuMain menu Projector adjustment PRJ-ADJ1/2 menu Using the Menu Screen Menu Selections Quick Start MenuPress Menu ExampleExample Adjusting Bright Quick Start MenuMenu Selections Complete Menu Following items can be configured on the Quick Start MenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press EnterSelecting the Picture Mode Picture Adjustment Picture MenuMenu operation n Adjusting the Image Adjusting the Color TemperatureAdjusting the Colors Adjusting Hue, Saturation, or ValueEco+Quiet Selecting the Film ModeReducing Image Noise DNR Resolution Setting Signal Adjustment SIG-ADJ MenuSignal Type Setting Setting the Video System Setting the Video SetupChecking the Input Signal When reproducing Ntsc signals in PAL video equipmentAdjusting the Projected Image SCR-ADJ Menu Setting the Resize ModeAdjusting the Image Position Keystone CorrectionSetting the Overscan Setting the On-screen DisplayClosed Caption For Americas onlySelecting the Setup Guide Selecting the Background ImageReversing/Inverting Projected Images Selecting the Wall ColorAuto Sync Auto Sync Adjustment Auto Power Off FunctionSpeaker Setting Fan Mode SettingTo cancel the keycode that you have already set When the System Lock is setSystem Lock Function Enter the same keycode in Re- confirmAdjusting the Projector Function PRJ-ADJ1/2 Menu Keylock FunctionTaking the Keylock Off Select On, then press EnterSetting the Function Button Operation Standby ModeReturning to the Default Settings Selecting the Quick Start MenuPrecautions on Viewing Stereoscopic 3D Images Viewing Stereoscopic 3D ImagesInformation on the 3D Projection Function Shutter glasses control light signalAppendix Projecting 3D images Using 3D Viewing ModeEnding 3D projection Maintenance Cleaning the projectorMaintenance Indicators About the temperature warning indicatorAbnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitSTANDBY/ON button AC socket Resetting the Lamp Timer RS-232C Specifications and Commands Computer controlCommunication conditions Basic formatCommands Computer ProjectorRGB PAL CC1 Compatibility Chart ComputerDTV Troubleshooting 19-2253, 54 Problem Check For Sharp Assistance Sharp Electronics FranceSpecifications Dimensions Units inches mmIndex
Related manuals
Manual 75 pages 34.96 Kb