Sharp PG-LW2000 Setting the Video System, Setting the Video Setup, Checking the Input Signal

Page 44

Signal Adjustment (“SIG-ADJ” Menu) (Continued)

Menu operation n Page 36

5 Setting the Video System

The video input system mode is factory preset to “Auto”; however, a clear picture from the connected audio-visual equipment may not be received, depending on the Video signal difference.

In that case, switch the Video signal.

Selectable items

Auto

PAL

SECAM

*NTSC4.43

NTSC3.58

PAL-M

PAL-N

PAL-60

*When reproducing NTSC signals in PAL video equipment.

Note

•The Video signal can only be set in VIDEO mode.

•When “Video System” is set to “Auto”, you may not receive a clear picture due to signal differences. Should this occur, switch to the video system of the source signal.

6 Setting the Video Setup

Selectable	Description
items	Description
items

0 IRE	Sets the black level to 0 IRE.
7.5 IRE	Sets the black level to 7.5	IRE.

Note

•This function is available for the following signals.

With COMPUTER/COMPONENT input: - 480I

With VIDEO input: - NTSC3.58

7 Checking the Input Signal

This function allows you to check the current input signal information.

42

Image 44

Contents PG-LW2000 Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Accessories Optional accessoriesContents Reference Viewing Stereoscopic 3D ImagesCleaning Power SourcesAccessories Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Other connected equipment Using the projector in other countriesTemperature monitor function Part Names and Functions 15 16Rear View Terminals Part Names and Functions Usable Range Remote control signal transmittersInserting the Batteries Setup and Projection Easy StartInput list Correcting trapezoidal distortion using Keystone CorrectionOn the remote control Setting Up the Projector Video SetupSetting Up the Projector Standard Setup Front ProjectionScreen Lens center Signal Input Normal ModeScreen Size and Projection Distance Projection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment You may need other cables or connectors not listed belowConnecting the Projector to Other Equipment Connecting the Power Cord AC socket To AC outlet Power cord suppliedRS-232C Terminal D-sub 9 pin male connector Controlling the Projector by a ComputerTurning the Projector On Power indicator Lamp indicatorTurning the Projector On/Off About the Setup Guide Adjusting the Projected Image Adjusting the FocusPress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Height Adjusting the Picture SizeUse the rear adjustment foot to make the projector level Rotate the zoom ring to enlarge or shrink the picture sizeCorrecting Trapezoidal Distortion Press KeystoneVOL +/- Volume buttons Input buttons AV Mute button Buttons Switching the Input ModeAdjusting the Volume Button Resize ModePress Resize About Copyrights Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreezing a Moving Image Displaying an Enlarged Portion of an ImageMenu Items Picture menuMain menu Projector adjustment PRJ-ADJ1/2 menu Using the Menu Screen Menu Selections Quick Start MenuPress Menu ExampleExample Adjusting Bright Quick Start MenuMenu Selections Complete Menu Following items can be conﬁgured on the Quick Start MenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press EnterMenu operation n Picture Adjustment Picture MenuSelecting the Picture Mode Adjusting the Image Adjusting the Color TemperatureAdjusting the Colors Adjusting Hue, Saturation, or ValueReducing Image Noise DNR Selecting the Film ModeEco+Quiet Signal Type Setting Signal Adjustment SIG-ADJ MenuResolution Setting Setting the Video System Setting the Video SetupChecking the Input Signal When reproducing Ntsc signals in PAL video equipmentAdjusting the Projected Image SCR-ADJ Menu Setting the Resize ModeAdjusting the Image Position Keystone CorrectionSetting the Overscan Setting the On-screen DisplayClosed Caption For Americas onlySelecting the Setup Guide Selecting the Background ImageReversing/Inverting Projected Images Selecting the Wall ColorAuto Sync Auto Sync Adjustment Auto Power Off FunctionSpeaker Setting Fan Mode SettingTo cancel the keycode that you have already set When the System Lock is setSystem Lock Function Enter the same keycode in Re- conﬁrmAdjusting the Projector Function PRJ-ADJ1/2 Menu Keylock FunctionTaking the Keylock Off Select On, then press EnterSetting the Function Button Operation Standby ModeReturning to the Default Settings Selecting the Quick Start MenuPrecautions on Viewing Stereoscopic 3D Images Viewing Stereoscopic 3D ImagesAppendix Shutter glasses control light signalInformation on the 3D Projection Function Ending 3D projection Using 3D Viewing ModeProjecting 3D images Maintenance Cleaning the projectorMaintenance Indicators About the temperature warning indicatorAbnormally high Are high Lower than 95F +35ºC Replacing the Lamp Regarding the LampLamp STANDBY/ON button AC socket Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer RS-232C Speciﬁcations and Commands Computer controlCommunication conditions Basic formatCommands Computer ProjectorRGB PAL CC1 Compatibility Chart ComputerDTV Troubleshooting 19-2253, 54 Problem Check For Sharp Assistance Sharp Electronics FranceSpeciﬁcations Dimensions Units inches mmIndex

Related manuals

Manual 75 pages 34.96 Kb