Sharp PGLW2000, PG-LW2000 appendix Turning the Projector On/Off, Power indicator Lamp indicator

Page 25

Turning the Projector On/Off

Turning the Projector On

Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 19 to 21.)

Press STANDBY/ON on the projector or ON on the remote control.

•The power indicator illuminates green.

•After the lamp indicator illuminates, the projector is ready to start operation.

Note

•About the Lamp Indicator

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on.

Blinking in green: The lamp is warming up.

Red: The lamp is shut down abnormally or the lamp should be replaced.

•When switching on the projector, a slight

ﬂ ickering of the image may be experienced within the ﬁ rst minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.

•If the projector is put into Standby mode and immediately turned on again, the lamp may take some time to start projection.

•When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 47 for details.

Turning the Power Off (Putting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the conﬁrmation message is displayed, to put the projector into Standby mode.

• The projector cannot be turned on while cooling.

Info

•When “Auto Restart” is set to “On”:

If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page 46.)

•English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 45.

Power indicator

Lamp indicator

STANDBY/ON button

STANDBY button

ON button

On-screen display (conﬁrmation message)

Info

•Direct Power Off function:

You can unplug the power cord from the AC outlet even if the cooling fan is still running.

Basic Operation

23

Image 25

Contents PG-LW2000 Model No Serial No Void the users authority to operate this equipment See bottom of projectorInformation Product Disposal Optional accessories AccessoriesContents Viewing Stereoscopic 3D Images ReferencePower Sources CleaningAccessories Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment 15 16 Part Names and FunctionsRear View Terminals Part Names and Functions Inserting the Batteries Remote control signal transmittersUsable Range Easy Start Setup and ProjectionOn the remote control Correcting trapezoidal distortion using Keystone CorrectionInput list Video Setup Setting Up the ProjectorSetting Up the Projector Standard Setup Front ProjectionScreen Size and Projection Distance Signal Input Normal ModeScreen Lens center Ceiling-Mount Setup Projection PRJ ModeYou may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment AC socket To AC outlet Power cord supplied Connecting the Power CordControlling the Projector by a Computer RS-232C Terminal D-sub 9 pin male connectorTurning the Projector On/Off Power indicator Lamp indicatorTurning the Projector On Adjusting the Projected Image Adjusting the Focus About the Setup GuidePress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Picture Size Adjusting the HeightUse the rear adjustment foot to make the projector level Rotate the zoom ring to enlarge or shrink the picture sizePress Keystone Correcting Trapezoidal DistortionAdjusting the Volume Switching the Input ModeVOL +/- Volume buttons Input buttons AV Mute button Buttons Press Resize Resize ModeButton About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImagePicture menu Menu ItemsMain menu Projector adjustment PRJ-ADJ1/2 menu Menu Selections Quick Start Menu Using the Menu ScreenPress Menu ExampleQuick Start Menu Example Adjusting BrightMenu Selections Complete Menu Following items can be conﬁgured on the Quick Start MenuPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press EnterSelecting the Picture Mode Picture Adjustment Picture MenuMenu operation n Adjusting the Color Temperature Adjusting the ImageAdjusting the Colors Adjusting Hue, Saturation, or ValueEco+Quiet Selecting the Film ModeReducing Image Noise DNR Resolution Setting Signal Adjustment SIG-ADJ MenuSignal Type Setting Setting the Video Setup Setting the Video SystemChecking the Input Signal When reproducing Ntsc signals in PAL video equipmentSetting the Resize Mode Adjusting the Projected Image SCR-ADJ MenuAdjusting the Image Position Keystone CorrectionSetting the On-screen Display Setting the OverscanClosed Caption For Americas onlySelecting the Background Image Selecting the Setup GuideReversing/Inverting Projected Images Selecting the Wall ColorAuto Power Off Function Auto Sync Auto Sync AdjustmentSpeaker Setting Fan Mode SettingWhen the System Lock is set To cancel the keycode that you have already setSystem Lock Function Enter the same keycode in Re- conﬁrmKeylock Function Adjusting the Projector Function PRJ-ADJ1/2 MenuTaking the Keylock Off Select On, then press EnterStandby Mode Setting the Function Button OperationReturning to the Default Settings Selecting the Quick Start MenuViewing Stereoscopic 3D Images Precautions on Viewing Stereoscopic 3D ImagesInformation on the 3D Projection Function Shutter glasses control light signalAppendix Projecting 3D images Using 3D Viewing ModeEnding 3D projection Cleaning the projector MaintenanceAbout the temperature warning indicator Maintenance IndicatorsAbnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitSTANDBY/ON button AC socket Resetting the Lamp Timer Computer control RS-232C Speciﬁcations and CommandsCommunication conditions Basic formatComputer Projector CommandsRGB PAL CC1 Computer Compatibility ChartDTV 19-22 Troubleshooting53, 54 Problem Check Sharp Electronics France For Sharp AssistanceSpeciﬁcations Units inches mm DimensionsIndex

Related manuals

Manual 75 pages 34.96 Kb