Sharp PG-LW2000, PGLW2000 appendix Maintenance Indicators, About the temperature warning indicator

Page 56

Maintenance Indicators

The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.

If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter Standby mode. After the projector has entered Standby mode, follow the procedures given below.

Top View Temperature warning indicator

Lamp indicator

Power indicator

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising,

” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. When you fi nd the temperature warning indicator blinking, be sure to perform the measures described on page 55.

About the lamp indicator

When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter Standby mode. At this time, the lamp indicator will illuminate in red.

If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.

Indicators on the Projector

Power indicator

Red on

Normal (Standby)

 

Green on

Normal (Power on)

 

Red blinks

Abnormal (See page 55.)

 

Green blinks

Normal (Cooling)

Lamp indicator

Green on

Normal

 

Green blinks

The lamp is warming up.

 

Red on

The lamp is shut down abnormally or requires to be

 

 

changed. (See page 55.)

Temperature

Off

Normal

warning indicator

Red on/Red blinks

The internal temperature is abnormally high. (See page 55.)

54

Image 56
Contents PG-LW2000 Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Accessories Optional accessoriesContents Reference Viewing Stereoscopic 3D ImagesCleaning Power SourcesAccessories Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Other connected equipment Using the projector in other countriesTemperature monitor function Part Names and Functions 15 16Rear View Terminals Part Names and Functions Usable Range Remote control signal transmittersInserting the Batteries Setup and Projection Easy StartInput list Correcting trapezoidal distortion using Keystone CorrectionOn the remote control Setting Up the Projector Video SetupSetting Up the Projector Standard Setup Front ProjectionScreen Lens center Signal Input Normal ModeScreen Size and Projection Distance Projection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment You may need other cables or connectors not listed belowConnecting the Projector to Other Equipment Connecting the Power Cord AC socket To AC outlet Power cord suppliedRS-232C Terminal D-sub 9 pin male connector Controlling the Projector by a ComputerTurning the Projector On Power indicator Lamp indicatorTurning the Projector On/Off About the Setup Guide Adjusting the Projected Image Adjusting the FocusPress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Height Adjusting the Picture SizeUse the rear adjustment foot to make the projector level Rotate the zoom ring to enlarge or shrink the picture sizeCorrecting Trapezoidal Distortion Press KeystoneVOL +/- Volume buttons Input buttons AV Mute button Buttons Switching the Input ModeAdjusting the Volume Button Resize ModePress Resize About Copyrights Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreezing a Moving Image Displaying an Enlarged Portion of an ImageMenu Items Picture menuMain menu Projector adjustment PRJ-ADJ1/2 menu Using the Menu Screen Menu Selections Quick Start MenuPress Menu ExampleExample Adjusting Bright Quick Start MenuMenu Selections Complete Menu Following items can be configured on the Quick Start MenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press EnterMenu operation n Picture Adjustment Picture MenuSelecting the Picture Mode Adjusting the Image Adjusting the Color TemperatureAdjusting the Colors Adjusting Hue, Saturation, or ValueReducing Image Noise DNR Selecting the Film ModeEco+Quiet Signal Type Setting Signal Adjustment SIG-ADJ MenuResolution Setting Setting the Video System Setting the Video SetupChecking the Input Signal When reproducing Ntsc signals in PAL video equipmentAdjusting the Projected Image SCR-ADJ Menu Setting the Resize ModeAdjusting the Image Position Keystone CorrectionSetting the Overscan Setting the On-screen DisplayClosed Caption For Americas onlySelecting the Setup Guide Selecting the Background ImageReversing/Inverting Projected Images Selecting the Wall ColorAuto Sync Auto Sync Adjustment Auto Power Off FunctionSpeaker Setting Fan Mode SettingTo cancel the keycode that you have already set When the System Lock is setSystem Lock Function Enter the same keycode in Re- confirmAdjusting the Projector Function PRJ-ADJ1/2 Menu Keylock FunctionTaking the Keylock Off Select On, then press EnterSetting the Function Button Operation Standby ModeReturning to the Default Settings Selecting the Quick Start MenuPrecautions on Viewing Stereoscopic 3D Images Viewing Stereoscopic 3D ImagesAppendix Shutter glasses control light signalInformation on the 3D Projection Function Ending 3D projection Using 3D Viewing ModeProjecting 3D images Maintenance Cleaning the projectorMaintenance Indicators About the temperature warning indicatorAbnormally high Are high Lower than 95F +35ºC Replacing the Lamp Regarding the LampLamp STANDBY/ON button AC socket Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer RS-232C Specifications and Commands Computer controlCommunication conditions Basic formatCommands Computer ProjectorRGB PAL CC1 Compatibility Chart ComputerDTV Troubleshooting 19-2253, 54 Problem Check For Sharp Assistance Sharp Electronics FranceSpecifications Dimensions Units inches mmIndex
Related manuals
Manual 75 pages 34.96 Kb