Eiki LC-XS25, LC-XS30 Remote Control Battery Installation, Operating Range, Two AA size batteries

Page 12

Part Names and Functions

Remote Control Battery Installation

1

Open the battery

 

compartment lid.

2

Install new batteries

 

into the compartment.

Two AA size batteries

For correct polarity

(+ and –), be sure battery terminals are in contact with pins in the compartment.

3

Replace the

 

compartment lid.

To ensure safe operation, please observe the following precautions:

Use two (2) AA or LR6 type alkaline batteries.

Always replace batteries in sets.

Do not use a new battery with a used battery.

Avoid contact with water or liquid.

Do not expose the remote control to moisture or heat.

Do not drop the remote control.

If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.

Risk of explosion if a battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

Operating Range

Point the remote control toward the projector (Infrared Remote Receiver) when pressing any button. Maximum operating range for the remote control is about 16.4' (5 m) and 60° in front of the projector.

16.4' (5 m)

12

Image 12
Contents Model LC-XS25 LC-XS30 Features and Design Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Installing the Projector in Proper Position Air CirculationMoving the Projector Compliance Federal Communications Commission NoticePart Names and Functions FrontBack Bottom Rear Terminal ① Control PortTop Control Remote Control Remote Control Battery Installation Operating RangeTwo AA size batteries Installation Adjustable FeetPositioning the Projector Connecting to a Computer Cables used for connectionConnecting to Video Equipment NoteConnecting to Component Video and RGB Scart Equipment Connecting the AC Power Cord  NoteProjector side Selected Input Source and Lamp Mode Basic OperationTurning On the Projector PIN Code Input Dialog BoxTurning Off the Projector How to Operate the On-Screen Menu Remote ControlTop Control On-Screen MenuMenu Bar Zoom and Focus Adjustment Auto setup functionKeystone Correction Sound Adjustment Remote Control OperationTimer button Auto SET buttonZoom buttons No Show buttonComputer 1 Analog Computer 1 Digital Video Remote Control Computer InputInput Source Selection RGB Computer 1 Analog/Computer Direct OperationInput Source Selection Rgbpc digital, Rgbav Hdcp Computer 1 buttonComputer System Selection Selecting Computer System ManuallyPC System Menu Auto PC Adjustment To store adjustment parametersMenu Operation Auto PC Adj Manual PC Adjustment Reset Mode freeTo clear adjusted data To store adjusted dataImage Level Selection Image Select Menu icon Image Level Adjustment Screen Size Adjustment NormalTrue Wide FullCustom For zooming in and out the images Digital zoom + Digital zoomZoom button Video Input Input Source Selection Video, S-videoSource Select Menu Video Video buttonInput Source Selection Component, RGB Scart 21-pin Computer 2 button Component buttonRGB Scart Video System Selection AutoAV System Menu Video or S-video AV System Menu ComponentCinema Image button Dynamic StandardImage User preset image in the Image Adjust Menu. pp.42-43 Color TintNoise reduction ProgressiveProvide the image at a normal video aspect ratio Setting SettingSetting Menu Language LanguageAuto setup Input search Auto Keystone Keystone Blue backDisplay Logo Logo and Logo PIN code lock settings Logo selectCapture Logo select CaptureTo Enter the Logo PIN code Logo PIN code lockStandby mode Ceiling Rear Power managementCeiling RearOn start Note Filter controlSecurity Key lock and PIN code lock settings Key lockPIN code lock Change the PIN code lock setting Change the PIN codeFan Lamp counterFactory default Filter counterMaintenance and Care Filter InstructionsReplacing the Filter Cartridge RecommendationResetting the Filter Counter Resetting the Scroll CounterScroll counter Lamp Replacement Lamp replacement icon NoteOrder Replacement Lamp Reset the lamp replacement counterLamp Handling Precautions Resetting the Lamp CounterIndicator is blinking red Indicator emits a red lightProjector is shut down and the Warning Temp Then check the matters belowCleaning the Lens Cover Cleaning the Projector CabinetTroubleshooting AppendixCheck the Input signal. Auto PC function can not work when Signal is input into DVI terminal. seePower management function can not work while Freeze or No Show function is running. see pages 23,24Remote Control does not work PC Adjust Menu TreeInput SoundImage Select Image Adjust Screen System Image Select Image AdjustSetting Indicators and Projector Condition Projector is off. The AC power cord is unpluggedProjector is operating normally Red OrangeProjector Condition Compatible Computer Specifications FreqNotes KHzTechnical Specifications Accessories Optional PartsCOMPONENT-VGA Cable AH-98771 SCART-VGA Cable AH-98881 Model NoConfigurations of Terminals Control Port Connector D-sub 9 pinTerminal Analog RGB Mini D-sub 15 pin Dimensions Unit inch mmLogo PIN Code Lock No PIN Code Number MemoEiki International, Inc