Eiki LC-XS30, LC-XS25 owner manual Order Replacement Lamp, Reset the lamp replacement counter

Page 61

Maintenance and Care

Follow these steps to replace the lamp.

1	Turn off the projector and disconnect the AC power
	cord. Allow the projector to cool for at least 45
	minutes.
2	Loosen the screw with a screwdriver, slide and open
	the lamp cover.
3	Loosen 2 screws of the lamp with a screwdriver and
	pull out the lamp upwards vertically by grasping the
	handle.
4	Replace the lamp with a new one and tighten the 2
	screws back into position. Make sure that the lamp is
	set properly. Replace the lamp cover and tighten the
	screw.
5	Connect the AC power cord to the projector and turn
	on the projector.
6	Reset the lamp replacement counter..
	See "Resetting the Lamp Counter" on the next page .

Screw

Lamp Cover

Screw

Handle Screw

Lamp

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer.

● Model No. of your projector	: LC-XS25/LC-XS30
● Replacement Lamp Type No.	: POA-LMP127
	(Service Parts No. 610 339 8600)

61

Image 61

Contents Model LC-XS25 LC-XS30 Features and Design Table of Contents Risk of Electric Shock Do not Open To the OwnerSafety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector Federal Communications Commission Notice ComplianceFront Part Names and FunctionsBack Bottom① Control Port Rear TerminalTop Control Remote Control Operating Range Remote Control Battery InstallationTwo AA size batteries Adjustable Feet InstallationPositioning the Projector Cables used for connection Connecting to a ComputerNote Connecting to Video EquipmentConnecting to Component Video and RGB Scart Equipment  Note Connecting the AC Power CordProjector side Basic Operation Selected Input Source and Lamp ModeTurning On the Projector PIN Code Input Dialog BoxTurning Off the Projector Remote Control How to Operate the On-Screen MenuTop Control On-Screen MenuMenu Bar Auto setup function Zoom and Focus AdjustmentKeystone Correction Remote Control Operation Sound AdjustmentAuto SET button Timer buttonZoom buttons No Show buttonComputer Input Computer 1 Analog Computer 1 Digital Video Remote ControlInput Source Selection RGB Computer 1 Analog/Computer Direct OperationComputer 1 button Input Source Selection Rgbpc digital, Rgbav HdcpSelecting Computer System Manually Computer System SelectionPC System Menu To store adjustment parameters Auto PC AdjustmentMenu Operation Auto PC Adj Manual PC Adjustment Mode free ResetTo clear adjusted data To store adjusted dataImage Level Selection Image Select Menu icon Image Level Adjustment Normal Screen Size AdjustmentTrue Full WideCustom Digital zoom For zooming in and out the images Digital zoom +Zoom button Input Source Selection Video, S-video Video InputSource Select Menu Video Video buttonComputer 2 button Component button Input Source Selection Component, RGB Scart 21-pinRGB Scart Auto Video System SelectionAV System Menu Video or S-video AV System Menu ComponentImage button Dynamic Standard CinemaImage User preset image in the Image Adjust Menu. pp.42-43 Tint ColorProgressive Noise reductionProvide the image at a normal video aspect ratio Setting SettingSetting Menu Language LanguageInput search  Auto setupAuto Keystone Blue back KeystoneDisplay Logo select Logo Logo and Logo PIN code lock settingsCapture Logo select CaptureLogo PIN code lock To Enter the Logo PIN codeCeiling Rear Power management Standby modeCeiling RearOn start Filter control NoteKey lock Security Key lock and PIN code lock settingsPIN code lock Change the PIN code Change the PIN code lock settingLamp counter FanFilter counter Factory defaultFilter Instructions Maintenance and Care Recommendation Replacing the Filter CartridgeResetting the Scroll Counter Resetting the Filter CounterScroll counter Lamp replacement icon Note Lamp ReplacementReset the lamp replacement counter Order Replacement LampResetting the Lamp Counter Lamp Handling PrecautionsIndicator emits a red light Indicator is blinking redProjector is shut down and the Warning Temp Then check the matters belowCleaning the Projector Cabinet Cleaning the Lens CoverAppendix TroubleshootingSignal is input into DVI terminal. see Check the Input signal. Auto PC function can not work whenPower management function can not work while Freeze or No Show function is running. see pages 23,24Remote Control does not work Menu Tree PC AdjustInput SoundSystem Image Select Image Adjust Image Select Image Adjust ScreenSetting Projector is off. The AC power cord is unplugged Indicators and Projector ConditionProjector is operating normally Red OrangeProjector Condition Freq Compatible Computer SpecificationsKHz NotesTechnical Specifications Optional Parts AccessoriesCOMPONENT-VGA Cable AH-98771 SCART-VGA Cable AH-98881 Model NoControl Port Connector D-sub 9 pin Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin Unit inch mm DimensionsPIN Code Number Memo Logo PIN Code Lock NoEiki International, Inc