Eiki LC-XS30, LC-XS25 owner manual Installation, Positioning the Projector, Adjustable Feet

Page 13

Installation

Positioning the Projector

For projector positioning, see the figures below. The projector should be set horizontally to the flat screen.

Notes:

The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image.

The values shown below are approximate and may vary from the actual sizes.

41.8' (12.7 m)

34.8' (10.6 m)

23.2' (7.1 m)

17.4' (5.3 m)

11.6' (3.5 m)

4.6' (1.4 m)

Screen Size

 

40"

 

100"

150"

200"

300"

(W x H) mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 : 3 aspect ratio

 

813 x 610

 

2032 x 1524

3048 x 2286

4064 x 3048

6096 x 4572

 

 

 

 

 

 

 

 

Zoom (max)

 

4.6' (1.4 m)

 

11.6' (3.5 m)

17.4' (5.3 m)

23.2' (7.1 m)

34.8' (10.6 m)

 

 

 

 

 

 

 

 

Zoom (min)

 

5.5' (1.7 m)

 

13.9' (4.2 m)

20.9' (6.4 m)

27.8' (8.5 m)

41.8' (12.7 m)

Adjustable Feet

Projection angle can be adjusted up to 10.0 degrees with the adjustable feet.

1 Lift the front of the projector and push the feet lock latches on the projector.

2 Release the feet lock latches to lock the adjustable feet and rotate the adjustable feet to adjust the position and tilt.

3 To retract the adjustable feet, lift the front of the projector and push and undo the feet lock latches. Keystone distortion of the projected image can be corrected with the remote control or menu operation. (pp.22, 46)

Adjustable Feet

Feet Lock Latches

13

Image 13
Contents Model LC-XS25 LC-XS30 Features and Design Table of Contents Risk of Electric Shock Do not Open To the OwnerSafety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector Federal Communications Commission Notice ComplianceFront Part Names and FunctionsBack Bottom① Control Port Rear TerminalTop Control Remote Control Operating Range Remote Control Battery InstallationTwo AA size batteries Adjustable Feet InstallationPositioning the Projector Cables used for connection Connecting to a ComputerNote Connecting to Video EquipmentConnecting to Component Video and RGB Scart Equipment  Note Connecting the AC Power CordProjector side Basic Operation Selected Input Source and Lamp ModeTurning On the Projector PIN Code Input Dialog BoxTurning Off the Projector Remote Control How to Operate the On-Screen MenuTop Control On-Screen MenuMenu Bar Auto setup function Zoom and Focus AdjustmentKeystone Correction Remote Control Operation Sound AdjustmentAuto SET button Timer buttonZoom buttons No Show buttonComputer Input Computer 1 Analog Computer 1 Digital Video Remote ControlInput Source Selection RGB Computer 1 Analog/Computer Direct OperationComputer 1 button Input Source Selection Rgbpc digital, Rgbav HdcpSelecting Computer System Manually Computer System SelectionPC System Menu To store adjustment parameters Auto PC AdjustmentMenu Operation Auto PC Adj Manual PC Adjustment Mode free ResetTo clear adjusted data To store adjusted dataImage Level Selection Image Select Menu icon Image Level Adjustment Normal Screen Size AdjustmentTrue Full WideCustom Digital zoom For zooming in and out the images Digital zoom +Zoom button Input Source Selection Video, S-video Video InputSource Select Menu Video Video buttonComputer 2 button Component button Input Source Selection Component, RGB Scart 21-pinRGB Scart Auto Video System SelectionAV System Menu Video or S-video AV System Menu ComponentImage button Dynamic Standard CinemaImage User preset image in the Image Adjust Menu. pp.42-43 Tint ColorProgressive Noise reductionProvide the image at a normal video aspect ratio Setting SettingSetting Menu Language LanguageInput search  Auto setupAuto Keystone Blue back KeystoneDisplay Logo select Logo Logo and Logo PIN code lock settingsCapture Logo select CaptureLogo PIN code lock To Enter the Logo PIN codeCeiling Rear Power management Standby modeCeiling RearOn start Filter control NoteKey lock Security Key lock and PIN code lock settingsPIN code lock Change the PIN code Change the PIN code lock settingLamp counter FanFilter counter Factory defaultFilter Instructions Maintenance and CareRecommendation Replacing the Filter CartridgeResetting the Scroll Counter Resetting the Filter CounterScroll counter Lamp replacement icon Note Lamp ReplacementReset the lamp replacement counter Order Replacement LampResetting the Lamp Counter Lamp Handling PrecautionsIndicator emits a red light Indicator is blinking redProjector is shut down and the Warning Temp Then check the matters belowCleaning the Projector Cabinet Cleaning the Lens CoverAppendix TroubleshootingSignal is input into DVI terminal. see Check the Input signal. Auto PC function can not work whenPower management function can not work while Freeze or No Show function is running. see pages 23,24Remote Control does not work Menu Tree PC AdjustInput SoundSystem Image Select Image Adjust Image Select Image Adjust ScreenSetting Projector is off. The AC power cord is unplugged Indicators and Projector ConditionProjector is operating normally Red OrangeProjector Condition Freq Compatible Computer SpecificationsKHz NotesTechnical Specifications Optional Parts AccessoriesCOMPONENT-VGA Cable AH-98771 SCART-VGA Cable AH-98881 Model NoControl Port Connector D-sub 9 pin Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin Unit inch mm DimensionsPIN Code Number Memo Logo PIN Code Lock NoEiki International, Inc