Minicom Advanced Systems 3000 Connecting CATx cables, Connecting the Broadcaster/Transmitter

Page 18

DS VISION 3000

System In

CATx cable from

Transmitter/Broadcaster or

Line Splitter/L or Receiver

DCL unit

Screen 1

Serial port /

 

device

System Out

CATx cable to Line Splitter/L or Receiver* unit

Screen 2

Serial port / device

 

 

Receiver

SYSTEMIN

SYSTEMOUT

SERIAL 1

SERIAL 2

5VDC

 

 

DCL side 1

 

 

 

 

 

 

 

 

 

 

1

2

 

 

 

 

Receiver

TUNING

AUDIO

VIDEO 1

 

VIDEO 2

Video

Speakers /

DCL side 2

 

 

 

 

 

 

Audio

 

 

 

 

 

 

 

* Receivers refers to any of the following:

Receivers

Receivers L

Receivers DCL

Speakers /

Video Audio

Figure 22 Receiver DCL connections

Connecting CATx cables

The connections are illustrated in Figure 21 and Figure 22 above.

Connecting the Broadcaster/Transmitter

Connect CATx cables to the System ports of the Broadcaster/Transmitter and the System In ports of Receivers/L/DCL or Line Splitters/L.

Connecting/cascading a Line Splitter/L

Connect CATx cables to the System Out ports of the Line Splitter/L and the System In ports of Receivers/L/DCL or further Line Splitters/L.

Cascading a Receiver DCL

Connect a CATx cable to the System Out port of the Receiver DCL and the System In port of a Receiver/L/DCL or Line Splitter/L.

Connecting to the power supply

Connect the Transmitter/Broadcaster and all Receiver and Line Splitter units to the power supply using the AC/DC adapters provided. If using third party power adapters, ensure correct polarity (Center negative) and voltage – see the Tech specs.

Once the system is connected the DS Vision system broadcasts to all remote monitors/speakers. Note! You can use the Service Utility provided to broadcast content to specific monitors or groups of monitors, see DS Vision system management on page 19 below.

17

Image 18
Contents DS Vision User Guide Table of Contents User Guide Trademarks Technical precautionsWelcome User guide feedbackFeatures IntroductionSystem components System overviewTransmitter / Broadcaster Receivers Broadcaster Unit 8 portReceiver side Receiver DCL Mounting the ReceiversLine Splitters Vesa standard screw holesLEDs LEDTuning Unit DS Vision applicationsLong cluster Pre-installation guidelines Twisted Pair wiring installation tipsDS Vision cables Broadcaster/Transmitter cablesConnecting the cables Broadcaster/Transmitter connectionsReceiver /Receiver L connections Receiver DCL connectionsConnecting/cascading a Line Splitter/L Connecting CATx cablesConnecting the Broadcaster/Transmitter Connecting to the power supplyAdjusting the picture quality TablesDS Vision system management Saving and exitingInstalling the Service utility Connecting the Serial Download cableCom port LanguageTopology Auto-detectCallouts Auto-detected topologyUpdate CheckManual Naming a port Saving a topologySaving a Group Deleting a Group Saving a GroupSelecting the ports to command Controlling the systemFrom the topology on the left hand side Selecting all Sending commandsFrom the icons on the right hand side Control of Receiver DCL monitorsSending/blocking video Sending/blocking a Serial commandSending/blocking a bi-directional Serial command Sending/blocking AudioTo tune from the Transmitter/Broadcaster position To tune from the Receiver L/DCL or Line Splitter/L positionTest card Tuning window from Line Splitter L position Red, Green, BlueRemote Tuning RGB signalsRemote tuning Select device web Service Gives an overview of the remote tuningService window Upgrading firmwareVersion line Service Display Data Channel DDC hotkeyBroadcaster’s Local Serial port Security Security windowTechnical specifications DDCDimensions Regional Offices
Related manuals
Manual 33 pages 40.44 Kb