Minicom Advanced Systems 3000 manual Technical specifications, Ddc

Page 42

DS VISION 3000

18.Technical specifications

		HDTV up to 1080p.
	Resolution	Up to 1920x1440 @ 60Hz.
	Resolution	Depending on the cable quality
		Depending on the cable quality

	Input/Output video signals	Analog signal red, green, blue 0.7v, p-p 75 Ohm

	Sync	TTL compatible

	Horizontal/Vertical sync polarity	Positive/Negative

	System cable	CATx(5/5e/6/7) UTP/FTP 2x4x24 AWG solid wire cable

	Maximum distance	300m / 1,000ft

	Skew compensation	Up to 63 nsec

	DDC	Complies with VESA DDC 2 specifications

	RS232 connection	Serial signals = RXD, TXD, DTR, DSR, RTS, CTS

	Serial baud rate	Up to 57,600 bps

		Stereo
		Frequency response: 20 Hz to 20 kHz, +/-1 dB.
		Signal-to-Noise Ratio (SNR): 80 dBA.
	Audio	Total Harmonic Distortion and Noise (THD+N): 0.017%.
	Audio	Stereo crosstalk: -70 dB.
		Stereo crosstalk: -70 dB.
		Input impedance: 10k Ohms.
		Line level output; supports multimedia speakers.
		Maximum I/O levels: 3.1Vp-p (line level).

	Serial	Broadcaster / Transmitter – DCE
	Serial	Receivers - DTE
		Receivers - DTE
	Recommended cables	Belden 1583 ENH UTP CAT 5E 4PR
	Recommended cables	Belden 1633 ENH FTP CAT 5E 4PR
		Belden 1633 ENH FTP CAT 5E 4PR

	Operating temperature	5°C to 40°C / 41°F to 104°F

	Storage temperature	-40°C to 70°C / -40°F to 158°F

	Warranty	3 years

41

Image 42

Contents DS Vision User Guide Table of Contents User Guide Trademarks Technical precautionsWelcome User guide feedbackFeatures IntroductionSystem components System overviewTransmitter / Broadcaster Receivers Broadcaster Unit 8 portReceiver side Receiver DCL Mounting the ReceiversLine Splitters Vesa standard screw holesLEDs LEDTuning Unit DS Vision applicationsLong cluster Pre-installation guidelines Twisted Pair wiring installation tipsDS Vision cables Broadcaster/Transmitter cablesConnecting the cables Broadcaster/Transmitter connectionsReceiver /Receiver L connections Receiver DCL connectionsConnecting/cascading a Line Splitter/L Connecting CATx cablesConnecting the Broadcaster/Transmitter Connecting to the power supplyAdjusting the picture quality TablesDS Vision system management Saving and exitingInstalling the Service utility Connecting the Serial Download cableCom port LanguageTopology Auto-detectCallouts Auto-detected topologyUpdate CheckManual Naming a port Saving a topologySaving a Group Deleting a Group Saving a GroupSelecting the ports to command Controlling the systemFrom the topology on the left hand side Selecting all Sending commandsFrom the icons on the right hand side Control of Receiver DCL monitorsSending/blocking video Sending/blocking a Serial commandSending/blocking a bi-directional Serial command Sending/blocking AudioTo tune from the Transmitter/Broadcaster position To tune from the Receiver L/DCL or Line Splitter/L positionTest card Tuning window from Line Splitter L position Red, Green, BlueRemote Tuning RGB signalsRemote tuning Select device web Service Gives an overview of the remote tuningService window Upgrading firmwareVersion line Service Display Data Channel DDC hotkeyBroadcaster’s Local Serial port Security Security windowTechnical specifications DDCDimensions Regional Offices

Related manuals

Manual 33 pages 40.44 Kb