CONTENTS
Parts and their functions
Front panel
ON | POWER |
|
|
| DVCPRO | DVCPRO 50 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| DV |
|
|
|
|
|
|
|
|
|
|
|
|
OFF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
METER |
|
|
|
|
| COUNTER ASSEM | VIDEO | CUE | TC | STAND BY PLAYER | RECORDER | JOG | SHTL | SLOW | |||
FULL/FINE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
L |
|
|
|
|
| RESET CH1 | CH2 | CH3 | CH4 |
|
|
|
|
|
|
|
|
MONITOR SELECT |
|
|
|
|
|
|
|
|
| EDIT |
| PLAY |
| REC |
|
|
|
R |
|
|
|
|
| A IN | INSERT | A OUT |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| TRIM |
|
|
|
|
|
|
|
|
|
|
|
|
|
| PREVIEW/PREVIEW | AUTO EDIT PREROLL |
| SET |
|
| REW |
| STOP |
| FF |
|
|
|
HEADPHONES | MONITOR MIX | INPUT SELECT |
|
|
|
|
|
|
|
|
|
|
| ||||
|
| IN |
| OUT |
|
|
|
|
|
|
|
| |||||
|
| VIDEO | AUDIO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CH1 | CH2 | CH3 | CH4 | TC |
|
| SUPER | REC INH | INT | TCG | MODE | CONTROL |
|
|
|
| REC LEVEL |
|
|
| UNITY | PRESET MENU SET DIAG | ON | ON | REGEN | TAPE | REMOTE |
|
|
| |||
|
|
|
|
|
|
|
|
|
| PRESET |
|
|
|
|
|
| |
| PB LEVEL |
|
|
| VAR |
|
| OFF | OFF | EXIT |
| EE | LOCAL |
|
|
| |
V X Z
W Y [
VDIAG button
When this button is pressed, the VTR information is displayed.
When it is pressed again, the original display is restored.
The VTR information consists of the HOURS METER information and WARNING information. Switching between the display of each type of information is accomplished by pressing the search button.
Displayed on the HOURS METER screen are the deck’s serial number,
Displayed on the WARNING screen are details of the warnings.
WSUPER switch ON:
The superimposed time code and other information is output to the VIDEO OUT 3 connector or SDI OUT 3 connector.
OFF:
The superimposed information is not output.
XREC INH switch
This switch is used to enable or disable recording on the cassette tape.
ON:
Recording on the cassette tape is disabled (inhibited).
In this state, the REC INH lamp lights on the display panel.
OFF:
Recording on the cassette tape is enabled so long as the accidental erasure prevention mechanism on the cassette tape is set to enable recording.
YTCG switch
REGEN:
The internal time code generator is synchronized with the time code which the time code reader has read from the tape.
The signal that is to be used for regeneration is selected using setup menu No. 503 (TCG REGEN).
PRESET:
The time code generator can be preset on the operation panel or by remote control.
EXT:
The external time code which is input from the time code input connector or video signal VITC is used. Which of the two is to be set is selected using setup menu No. 505 (EXT TC SEL).
ZMODE switch
<In the stop mode> TAPE:
The signal which is played back from the tape is output.
EE:
The input signal selected by the INPUT SELECT button is output.
<During recording or editing> TAPE:
The simultaneous playback signals are output. (The setup menu No.310 (CONFI EDIT) setting is necessary.)
EE:
The input signal selected by the INPUT SELECT button is output.
[CONTROL switch
This switch is set to the REMOTE or LOCAL position when the VTR is to be controlled by an external unit using the REMOTE,
REMOTE:
Set the switch to this position to control the VTR using a component that has been connected using the
LOCAL:
Set the switch to this position to control the VTR using its operation panel.
When the unit is to be controlled with the switch at this position by a component connected using the PARALLEL connector, selection can be made using setup menu No. 211 (LOCAL 25P).
11 (E)