Marantz MV5100 manual Vhs Et

Page 32

MV5100 27-84 7/21/00 10:59 AM Page 32

32 S-VHS ET

This VCR allows recording in Super VHS ET (Expansion Technology).You can play back those cassettes recorded in S-VHS ET on a VCR equipped with S-VHS ET.You can record with S-VHS picture quality on VHS cassettes.

1

Before you begin the recording, press the S-VHS ET but- ton on the front panel so that the button lights. S-VHS ET recording cannot be turned on or off during recording with the S- VHS ET button.

POWER

S-VHS ET

VCR/TV

OPEN A/V FRONT CONNECTORS

MENU

AUDIO

DUBBING

OK/STATUS

SUPER VHS ET

+8

 

4

SP SLP

0

 

6

 

-15dB

VCR

L NORM

REC/OTR

CHANNEL

HI-FI STEREO VIDEO CASSETTE RECORDER MV5100

STOP/EJECT

PAUSE/STILL PLAY

2

Press the S-VHS ET button again to cancel S-VHS ET recording.

Helpful Hints

Pressing the S-VHS ET button has no effect on an S-VHS tape.

To obtain the highest quality recording and to play pictures over a longer peri- od, S-VHS recording on S-VHS tape is recommended.

Label S-VHS ET recordings so you can easily distinguish them from regular VHS recordings.

S-VHS ET recordings also can be played on an S-VHS VCR or a VHS VCR equipped with SQPB (S-VHS QUASI PLAYBACK). However, there may be cases where S-VHS ET playback is not possible on a particular VCR.

Frequent still, frame-by-frame, and slow motion playback may damage the tape and cause the picture quality to decline.

With some tapes, better picture quality may not be obtained even with S-VHS ET recording.Test a recording first to make sure better results can be obtained.

Use high grade tapes for good results.

Image 32
Contents Model MV5100 User Guide Introduction PositioningFor Customer Use To prevent electrical shock, match wideFeatures Safety Precautions Declaration of ConformityIntroduction Repeat PlayTable of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR Maintenance/Video Head Cleaning Replace the battery compartment lidHookups without a Cable Box Disconnect the antenna or cable from your TVTV OUT Hookups without a Cable Box cont’dANT Cable Recording/Viewing Any Channel Hookups with a Cable Box/Direct Broadcast SystemConnections 1Cable signal Connect a Cable signal to the VCR’s Antenna in jackRecording One Channel/Watching Another 2RF coaxial cablePress the VCR button, then press the Power button Turning on Your VCRMenu shown below will appear Turn on the TVSAT CBL/DBS TV VCR VCR/TV Power Smartpicture MenuAutomatic Channel Setup Press the VCR button, then press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsPress the Play 8 or Stop 9 button to select ADD/DELETE CH., then press the OK/STATUS buttonSetting the Clock Manual Clock SettingChannels are set up. Details are on To make corrections, follow stepsDay increments Press the Play 8 or Stop 9 button repeatedly to setDate month and day. Every time you press the Play Setting the Clock cont’d Time Zone SelectionManual PBS Channel Selection VOL OK/STATUS MenuAutomatic PBS Channel Selection SAT CBL/DBS VCRPower Smartpicture Daylight-Savings TimeLanguage Selection Press the Play 8 or Stop 9 button to select LANDisplay Panel Front Panel Rear Panel VOLume 8/9 Button Power ButtonTV Button Play 8 ButtonTimer Button Turbo Timer ButtonSAT/CBL/DBS Button ALTernate Channel/SPEED ButtonIf on Screen Mode is set to on or Press the Play 8 or Stop 9 button to select onRepeat step 7PQRSFind the code for your SAT CBL/DBS VCR VCR/TV PowerTurn on your Cable Box/DBS Read and follow the steps below to play a tape Playback options and features are on pagesPlaying VCR records in a preset volume RecordingPress the VCR button Appear on the display panelVHS Recording VCR SET UP menu will appearVOL OK/STATUS Menu Timer VHS ET Recording One Channel/Watching Another VCR light will disappear from the display panelStarting an OTR Channels are set up. Details are on pagesOne-Touch Recording Record Link 1Set the program on the DBS Insert a tape in the VCRCall Letters Setting Up the VCR Plus+ Programming SystemChannels Setting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System If you forget to turn off the VCR To check your timer recordings, seeTime every week Channels are programmed. Details are on pages CBL/DBS VCR VCR/TV PowerQuick Programming Instructions continue on Tape SpeedsCassette type / Playback Time Tape Speed T160 T120 T60Quick Programming cont’d Press the OK/STATUS or Timer button. Program WAS Press the Power button to turn off the VCR. The r lightWill appear on the screen. If Program not Completed Appears, try again from stepTurbo Timer Insert a tape 1into the VCRChecking, Editing, or Clearing Timer Recordings Program ReviewIndicates a Weekly recording Indicates a Daily recordingOr, to cancel the timer recording, press the Clear button Program Overlap WarningBe highlighted in red Press the OK/STATUS button to select the programTimer Recording Speed Setting Follow the steps below to set Timer REC Speed to AutoAudio and video cables are not included Rerecording Tape DuplicationVCR 1 will play your tape. Insert a prerecorded tape in VCR Audio-dubbed tape Audio DubbingPre-recorded tape Connecting the Controller Use an RF coaxial cable toOn pages Turn on the Cable Box. Select a channel other thanInstructions continue on GHISetting the Controller to Operate a Cable Box cont’d Wait for a few secondsSetting the Controller to Operate a DBS SAT CBL/DBS TV VCR Setting the Controller to Operate a DBS cont’d7Wait for a few seconds Receiving a Second Audio Program Multi-Channel Television Sound SystemReceiving a Stereo Broadcast Multi-Channel Television Sound System cont’d Record the program as usual. Details are onHi-Fi Stereo Tape Playback Video Stabilizer Special effects playbackSmartPicture Digital Studio Picture Control Dspc does not work during a Record LinkSkip Search Press the Stop 9 button to cancel a Skip SearchIndex Search Playback Options Forward and Reverse SearchingViewing a Still Picture Viewing a Slow Motion PictureViewing Picture in Slow to Fast Motion LightHow to read the Tape Manager Directory Screen Tape ManagerFind a Title Insert a tape recorded with this VCRTo check memory Check Memory screen appearsTape Manager To Edit Tape Title and/or Program Title Title EditingEntering Character Choice of CategoryIf no cassette is inserted in the VCR Tape Manager To Find a Desired ProgramSorting by Number Smartpicture Sorting by DateCBL/DBS VCR/TV CBL/DBS TV VCR VCR/TV Power Smartpicture Sorting by CategoryTape Manager To Find a Blank Space cont’d Tape Manager To Delete Tape from Program Data Delete Tape DataIf you do not want to keep data of a particular tape Delete Program DataTape Manager To Disable Functions Menu screen appearsWhen Child Lock is activated Child LockCL will blink on the display panel CL will disappear from the display panelBlue Background Automatic Operation Features Glossary Cable Box/DBS Output Channel channel 03 orHelpful Hints Helpful Hints cont’d Specifications Remote control TimerVolume 8/9 button AutomaticIs a registered trademark