Marantz MV5100 manual Recording One Channel/Watching Another, 1Cable signal, 2RF coaxial cable

Page 9

MV5100 04-26 7/21/00 10:58 AM Page 9

Hookups with a Cable Box/Direct Broadcast System (cont’d) 9

With this connection:

•You may watch one channel while recording another.

•You may not record scrambled channels.

VCR

Cable Box/DBS

LP 20917-003

OUT IN

VHF/UHF

(MONO)

ANTENNA IN

S VIDEO

CABLE BOX

CH3 CH4

TV OUT

IN

1Cable signal

IN

OUT

2RF coaxial cable

75Ω
ANT	/
CABLE

TV’s

ANTENNA

3 IN jack RF coaxial cable

Connections

1

Connect a Cable signal to the VCR’s ANTENNA IN jack.

2

Use an RF coaxial cable (supplied) to connect the TV OUT jack on the VCR to the IN jack on the Cable Box/DBS.

3

Use a second RF coaxial cable to connect the OUT jack on the Cable Box/DBS to the TV’s ANTENNA IN jack.

Recording One Channel/Watching Another

1

Put the Cable Box/DBS on the same channel as the VCR’s CH3/CH4 switch. Set the TV to the Cable Box/DBS output chan- nel (03 or 04).

Then, with the VCR in VCR position (the VCR light will appear on the display panel), use the CH(annel) 8/9 button to select the channel you want to record at the VCR. Start the recording.

2

Press the VCR/TV button once to put the VCR in TV position. (The VCR light will disappear.)

3

Select the channel you want to watch at the Cable Box/DBS.

Helpful Hint

•When you play a tape, make sure the Cable Box/DBS is set to the same channel as the CH3/CH4 switch on the VCR. Set the TV to the Cable Box/DBS output channel (03 or 04).

Image 9

Contents Model MV5100 User Guide Positioning IntroductionFor Customer Use To prevent electrical shock, match wideSafety Precautions Declaration of Conformity FeaturesIntroduction Repeat PlayTable of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR Maintenance/Video Head Cleaning Replace the battery compartment lidDisconnect the antenna or cable from your TV Hookups without a Cable BoxHookups without a Cable Box cont’d ANT CableTV OUT Hookups with a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Connect a Cable signal to the VCR’s Antenna in jack 1Cable signalRecording One Channel/Watching Another 2RF coaxial cableTurning on Your VCR Press the VCR button, then press the Power buttonMenu shown below will appear Turn on the TVMenu SAT CBL/DBS TV VCR VCR/TV Power SmartpicturePress the VCR button, then press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the Play 8 or Stop 9 button to select ADD/DELETE CH., then press the OK/STATUS buttonManual Clock Setting Setting the ClockChannels are set up. Details are on To make corrections, follow stepsPress the Play 8 or Stop 9 button repeatedly to set Date month and day. Every time you press the PlayDay increments Time Zone Selection Setting the Clock cont’dVOL OK/STATUS Menu Manual PBS Channel SelectionSAT CBL/DBS VCR Automatic PBS Channel SelectionDaylight-Savings Time Power SmartpicturePress the Play 8 or Stop 9 button to select LAN Language SelectionDisplay Panel Front Panel Rear Panel Power Button VOLume 8/9 ButtonTV Button Play 8 ButtonTurbo Timer Button Timer ButtonSAT/CBL/DBS Button ALTernate Channel/SPEED ButtonPress the Play 8 or Stop 9 button to select on If on Screen Mode is set to on or7PQRS Repeat stepSAT CBL/DBS VCR VCR/TV Power Turn on your Cable Box/DBSFind the code for your Playback options and features are on pages PlayingRead and follow the steps below to play a tape Recording VCR records in a preset volumePress the VCR button Appear on the display panelVCR SET UP menu will appear VOL OK/STATUS Menu TimerVHS Recording VHS ET VCR light will disappear from the display panel Recording One Channel/Watching AnotherChannels are set up. Details are on pages One-Touch RecordingStarting an OTR 1Set the program on the DBS Insert a tape in the VCR Record LinkSetting Up the VCR Plus+ Programming System ChannelsCall Letters Setting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System To check your timer recordings, see Time every weekIf you forget to turn off the VCR CBL/DBS VCR VCR/TV Power Quick ProgrammingChannels are programmed. Details are on pages Tape Speeds Instructions continue onCassette type / Playback Time Tape Speed T160 T120 T60Quick Programming cont’d Press the Power button to turn off the VCR. The r light Press the OK/STATUS or Timer button. Program WASWill appear on the screen. If Program not Completed Appears, try again from stepInsert a tape 1into the VCR Turbo TimerProgram Review Checking, Editing, or Clearing Timer RecordingsIndicates a Weekly recording Indicates a Daily recordingProgram Overlap Warning Or, to cancel the timer recording, press the Clear buttonBe highlighted in red Press the OK/STATUS button to select the programFollow the steps below to set Timer REC Speed to Auto Timer Recording Speed SettingRerecording Tape Duplication VCR 1 will play your tape. Insert a prerecorded tape in VCRAudio and video cables are not included Audio Dubbing Pre-recorded tapeAudio-dubbed tape Use an RF coaxial cable to Connecting the ControllerTurn on the Cable Box. Select a channel other than On pagesInstructions continue on GHIWait for a few seconds Setting the Controller to Operate a Cable Box cont’dSetting the Controller to Operate a DBS Setting the Controller to Operate a DBS cont’d 7Wait for a few secondsSAT CBL/DBS TV VCR Multi-Channel Television Sound System Receiving a Stereo BroadcastReceiving a Second Audio Program Record the program as usual. Details are on Multi-Channel Television Sound System cont’dHi-Fi Stereo Tape Playback Special effects playback Video StabilizerSmartPicture Dspc does not work during a Record Link Digital Studio Picture ControlPress the Stop 9 button to cancel a Skip Search Index SearchSkip Search Forward and Reverse Searching Playback OptionsViewing a Still Picture Viewing a Slow Motion PictureLight Viewing Picture in Slow to Fast MotionTape Manager How to read the Tape Manager Directory ScreenFind a Title Insert a tape recorded with this VCRCheck Memory screen appears To check memoryTitle Editing Tape Manager To Edit Tape Title and/or Program TitleChoice of Category Entering CharacterTape Manager To Find a Desired Program Sorting by NumberIf no cassette is inserted in the VCR Sorting by Date CBL/DBS VCR/TVSmartpicture Sorting by Category CBL/DBS TV VCR VCR/TV Power SmartpictureTape Manager To Find a Blank Space cont’d Delete Tape Data Tape Manager To Delete Tape from Program DataIf you do not want to keep data of a particular tape Delete Program DataMenu screen appears Tape Manager To Disable FunctionsChild Lock When Child Lock is activatedCL will blink on the display panel CL will disappear from the display panelBlue Background Automatic Operation Features Cable Box/DBS Output Channel channel 03 or GlossaryHelpful Hints Helpful Hints cont’d Specifications Timer Remote controlVolume 8/9 button AutomaticIs a registered trademark