Marantz MV5100 manual Setting Up the VCR Plus+ Programming System, Channels, Call Letters

Page 36

MV5100 27-84 7/21/00 10:59 AM Page 36

36 Setting Up the VCR Plus+ Programming System

1

First, fill in the boxes on this page. It will only take a few minutes, and you must do it if you want the VCR Plus+ programming system to work properly.

Since the channel numbers of the stations you receive may not be the same as the station numbers, and since channel numbers differ from area to area, you must program the VCR with your local channel infor- mation.To fill in the boxes, you will need 1) a cable channel list, if applicable (you can request one from your cable company), and 2) a chart that lists VCR Plus+ channel numbers, which you can find in your TV guide or the TV listings of your local newspaper.

NOTE: If you are using a Cable Box/DBS and are not using the Controller, the Cable/TV channel must be 03 or 04 (the Cable Box/DBS output channel) for every VCR Plus+ channel.

Station

Channels

VCR PLUS+ CH. CABLE/TV CH.

Station

Channels

VCR PLUS+ CH. CABLE/TV CH.

Call Letters

Call Letters

Image 36

Contents Model MV5100 User Guide Introduction PositioningFor Customer Use To prevent electrical shock, match wideFeatures Safety Precautions Declaration of ConformityIntroduction Repeat PlayTable of Contents Putting Batteries in the Remote Control Using the Remote ControlVCR Maintenance/Video Head Cleaning Replace the battery compartment lidHookups without a Cable Box Disconnect the antenna or cable from your TVHookups without a Cable Box cont’d ANT CableTV OUT Hookups with a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel 1Cable signal Connect a Cable signal to the VCR’s Antenna in jackRecording One Channel/Watching Another 2RF coaxial cablePress the VCR button, then press the Power button Turning on Your VCRMenu shown below will appear Turn on the TVSAT CBL/DBS TV VCR VCR/TV Power Smartpicture MenuAutomatic Channel Setup Press the VCR button, then press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsPress the Play 8 or Stop 9 button to select ADD/DELETE CH., then press the OK/STATUS buttonSetting the Clock Manual Clock SettingChannels are set up. Details are on To make corrections, follow stepsPress the Play 8 or Stop 9 button repeatedly to set Date month and day. Every time you press the PlayDay increments Setting the Clock cont’d Time Zone SelectionManual PBS Channel Selection VOL OK/STATUS MenuAutomatic PBS Channel Selection SAT CBL/DBS VCRPower Smartpicture Daylight-Savings TimeLanguage Selection Press the Play 8 or Stop 9 button to select LANDisplay Panel Front Panel Rear Panel VOLume 8/9 Button Power ButtonTV Button Play 8 ButtonTimer Button Turbo Timer ButtonSAT/CBL/DBS Button ALTernate Channel/SPEED ButtonIf on Screen Mode is set to on or Press the Play 8 or Stop 9 button to select onRepeat step 7PQRSSAT CBL/DBS VCR VCR/TV Power Turn on your Cable Box/DBSFind the code for your Playback options and features are on pages PlayingRead and follow the steps below to play a tape VCR records in a preset volume RecordingPress the VCR button Appear on the display panelVCR SET UP menu will appear VOL OK/STATUS Menu TimerVHS Recording VHS ET Recording One Channel/Watching Another VCR light will disappear from the display panelChannels are set up. Details are on pages One-Touch RecordingStarting an OTR Record Link 1Set the program on the DBS Insert a tape in the VCRSetting Up the VCR Plus+ Programming System ChannelsCall Letters Setting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System To check your timer recordings, see Time every weekIf you forget to turn off the VCR CBL/DBS VCR VCR/TV Power Quick ProgrammingChannels are programmed. Details are on pages Instructions continue on Tape SpeedsCassette type / Playback Time Tape Speed T160 T120 T60Quick Programming cont’d Press the OK/STATUS or Timer button. Program WAS Press the Power button to turn off the VCR. The r lightWill appear on the screen. If Program not Completed Appears, try again from stepTurbo Timer Insert a tape 1into the VCRChecking, Editing, or Clearing Timer Recordings Program ReviewIndicates a Weekly recording Indicates a Daily recordingOr, to cancel the timer recording, press the Clear button Program Overlap WarningBe highlighted in red Press the OK/STATUS button to select the programTimer Recording Speed Setting Follow the steps below to set Timer REC Speed to AutoRerecording Tape Duplication VCR 1 will play your tape. Insert a prerecorded tape in VCRAudio and video cables are not included Audio Dubbing Pre-recorded tapeAudio-dubbed tape Connecting the Controller Use an RF coaxial cable toOn pages Turn on the Cable Box. Select a channel other thanInstructions continue on GHISetting the Controller to Operate a Cable Box cont’d Wait for a few secondsSetting the Controller to Operate a DBS Setting the Controller to Operate a DBS cont’d 7Wait for a few secondsSAT CBL/DBS TV VCR Multi-Channel Television Sound System Receiving a Stereo BroadcastReceiving a Second Audio Program Multi-Channel Television Sound System cont’d Record the program as usual. Details are onHi-Fi Stereo Tape Playback Video Stabilizer Special effects playbackSmartPicture Digital Studio Picture Control Dspc does not work during a Record LinkPress the Stop 9 button to cancel a Skip Search Index SearchSkip Search Playback Options Forward and Reverse SearchingViewing a Still Picture Viewing a Slow Motion PictureViewing Picture in Slow to Fast Motion LightHow to read the Tape Manager Directory Screen Tape ManagerFind a Title Insert a tape recorded with this VCRTo check memory Check Memory screen appearsTape Manager To Edit Tape Title and/or Program Title Title EditingEntering Character Choice of CategoryTape Manager To Find a Desired Program Sorting by NumberIf no cassette is inserted in the VCR Sorting by Date CBL/DBS VCR/TVSmartpicture CBL/DBS TV VCR VCR/TV Power Smartpicture Sorting by CategoryTape Manager To Find a Blank Space cont’d Tape Manager To Delete Tape from Program Data Delete Tape DataIf you do not want to keep data of a particular tape Delete Program DataTape Manager To Disable Functions Menu screen appearsWhen Child Lock is activated Child LockCL will blink on the display panel CL will disappear from the display panelBlue Background Automatic Operation Features Glossary Cable Box/DBS Output Channel channel 03 orHelpful Hints Helpful Hints cont’d Specifications Remote control TimerVolume 8/9 button AutomaticIs a registered trademark