JVC LPT0328 specifications 14 EN, Perform Preset Download, Set the video channel

Page 14

14 EN

INITIAL SETTINGS (cont.)

Preset Download

Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide Program Number Set

ATTENTION

You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

If you have connected the recorder to your TV via the AV connection ( pg. 10), the recorder will automatically perform Preset Download instead of the Auto Set Up in step 4 on page 13. After downloading, the recorder sets the clock and Guide Program numbers automatically.

Perform steps 1 to 3 of “Auto Set Up” on page 12 before continuing.

A Perform Preset Download.

Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.

On the front display panel

Press rt to select “CH – –” and press OK or e.

On the on-screen display

Press rt to move the highlight bar (pointer) to “T-V LINK” and press OK or

e.

Preset positions on the front display panel increase from “CH1”; do NOT press any button on the recorder or remote control until the front display panel shows clock time, “(CH) 1” or “– –:– –” as illustrated on page 15.

●If you are using the on-screen display, the T-V LINK screen

will appear. Then the GUIDE PROG SET screen will appear during Guide Program Number Set. When Preset Download is completed, “COMPLETED” appears for about 5 seconds, then the normal screen appears.

●If you press any button on the

recorder or remote control while downloading is in progress, it will be interrupted.

NOTES:

●For details, refer to the instruction manual of your TV.

●In the area where no TV station transmits a PDC (Programme Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.

●If there is a power cut, or if you press 1 or MENU while downloading or set up is in progress, it will be interrupted; be sure to turn off the recorder power once and try again from the beginning.

●Auto Clock Set may not function properly depending on the reception condition.

●On this recorder, the characters available for station names (ID) are A–Z, 0–9, –, f, + and I (space). Some names of

downloaded stations may differ from those of your TV ( pg. 76).

B Set the video channel.

Set the video channel to off manually. ( pg. 78)

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Inside View of Front Panel Rear View ON-SCREEN Display Remote Control How To Use Remote Control LCDSituate the recorder Check the contents10 EN Connect the recorder to TVVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsPlug the end of the mains power cord into a mains outlet Turn on the recorder Auto Set Up12 EN Select your countryPress rt to select your language code Perform Auto Set UpSelect the language Press rt to select Auto and press OK or eSet the video channel Perform Preset Download14 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 16 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link Basic Playback 20 ENHigh-Speed Turbo Search Variable Speed SearchSlow Motion Pause during playbackIndex Search 22 ENSkip Search Manual Index Mark/EraseRepeat Playback Next Function MemoryDigital TBC/NR Manual Tracking24 EN Audio signal during TimeScanTimeScan Activate Variable Speed SearchTimeScan 26 EN Instant Timer Recording ITR Tape Remaining TimeRetake Engage the Record-Pause mode28 EN Locate the start pointSuper VHS ET S-VHS ET Engage the S-VHS ET modeAdjust the audio recording level Audio Recording Level ControlReceived Receiving Stereo and Bilingual ProgrammesOn-screen Display Playback RecordingAccess the Showview Program screen Access the Showview displayAccess the Showview screen 32 ENSatellite Receiver Users Set the VPS/PDC modeEngage the recorder’s timer mode Guide Program Number SetExpress Timer Programming 34 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR+36 EN Select the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenProgramme Recording Select the L-2 Select modeRecording mode 38 ENSet the remote control code Remote A/B Code SwitchingRemove the power supply Re-supply the powerSet the TV brand code TV Multi-Brand Remote Control40 EN Operate the TVOperate the satellite receiver Satellite Receiver Multi-Brand Remote ControlSet the satellite receiver brand code Navigation Playback Navigation42 EN Check MemoryCheck the memory Turn Off NavigationVideo Navigation Title Screen Turn off Navigation44 EN Access the Find Blank Space screenEdit Title Find Blank SpaceEntering Character Access the Edit Title screenEdit Tape Title Select the tape titleSelect the programme 46 ENChoice of Category Enter the programme titleDelete the tape data Delete Tape DataDelete Programme Data Delete the programme data48 EN Access the Find Title screenFind Title Sort By Tape NumberSort By Date Access the Tape No. screenAccess the Date screen Select the programmeSort By Category Access the Category screen50 EN Category you want to watchEdit From a Camcorder Set the recorder’s input modeSet the edit mode Start the camcorderOutput/Input Set Select and L-2 Input Setting Decoder connectorAnother Video Recorder 54 ENRecorder Player Pre-recorded tape Audio-dubbed tape Audio Dubbing56 EN CD player, etcEnd Audio Dubbing Engage the Audio Dubbing modeStart dubbing Press AUX number key 0 and/or PR to select F-1 or S-1Source tape Before Insert Editing Recording tape Insert Editing58 EN After Insert EditingLocate the end point Engage the Insert Editing modeAV Insert Editing Start EditingLoad the source cassette Access the R.A.Edit screen60 EN Start playback of the source cassetteStart Random Assemble Editing Memory CapacityPrepare the recording deck End Random Assemble EditingPause Synchro Editing 62 ENStart Synchro Editing Press Synchro 7/79Jlip ID Number Access the Jlip ID No. Set screenSet the Jlip ID number ExamplesConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Satellite receiver Decoder Back of recorderConnect the decoder Select the input mode66 EN Set the tunerConnecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingWhen this function is set to ON, the timer is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture Off, and automatically disengaged when the recorder is70 EN For ExampleAbout Ntsc Playback 72 EN Access the Auto Channel Set screenTuner Set Auto Channel SetPress OK twice Perform Auto Channel SetView the Confirmation screen 74 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations B 76 ENSet Stations a TV Station And ID List Station NameVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 78 ENGuide Program Number Showview System SetupGuide Program Number Set Enter the Guide Program number80 EN Access the Clock Set screenClock Set Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationTroubleshooting 82 ENRecording Other Problems 84 ENPlayback 86 EN AV Insert Editing S.T. Picture System Preset DownloadTimer Warning Display TimeScan Tuner Set Clock SetInternational telephone Language code Country code
Top Page Image Contents