JVC LPT0328 specifications 76 EN, Set Stations a, Set Stations B

Page 76

76 EN

SUBSIDIARY SETTINGS (cont.)

Set Stations (A)

Set station names that are registered in your recorder.

Perform steps 1 and 2 of “Manual Channel Set” on page 74 to access the Confirmation screen before continuing.

A Select the item.

Press rt w e until the item you want begins blinking.

B Access the Manual Channel Set screen.

Press OK twice.

C Select the new station.

Press e until the station name (ID) begins blinking, then press rt until the new station’s name (ID) you want to store begins blinking. Registered station names ( pg. 77) appear as you press rt.

B Enter the new character.

Press rt to cycle through the characters (A–Z, 0–9, –, f, +, I (space) ) and stop when the desired character is indicated, then press e to enter. Enter the remaining characters the same way (maximum of 4). After entering all characters, press OK.

The Confirmation screen appears.

If you make a mistake, press w until the incorrect character begins blinking. Then enter the correct character by pressing rt.

C Close the Confirmation screen.

Press MENU.

NOTE:

The characters available for the station name (ID) are A–Z, 0–9, – , f, +, I (space) (maximum of 4).

Fine-Tuning Channels Already Stored

Perform steps 1 and 2 of “Manual Channel Set” on page 74 to access the Confirmation screen before continuing.

D Switch the stations.

Press OK.

The Confirmation screen appears.

Repeat steps 1 4 as necessary.

E Close the Confirmation screen.

Press MENU.

Set Stations (B)

Set station names other than the ones registered in your recorder.

Perform steps 1 and 2 of “Manual Channel Set” on page 74 to access the Confirmation screen and then perform steps 1 and 2 of “Set Stations (A)” above before continuing.

A Select the character for station name.

Press e until the first letter of the station name begins blinking.

A Select the channel to fine-tune.

Press rt w e until the channel you want to tune begins blinking.

B Access the Manual Channel Set screen.

Press OK twice. The Manual Channel Set screen appears.

C Perform tuning.

Press e until “+/–” begins blinking, then press rt until the picture is its clearest. Then press OK.

The Confirmation screen appears.

Repeat steps 1 3 as necessary.

D Close the Confirmation screen.

Press MENU.

Image 76
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Inside View of Front Panel Rear View ON-SCREEN Display Remote Control How To Use Remote Control LCDCheck the contents 10 ENSituate the recorder Connect the recorder to TVPlug the end of the mains power cord into a mains outlet 8To connect to a TV with S-VIDEO/AUDIO in connectorsVideo Connection Auto Set Up 12 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or ePerform Preset Download 14 ENSet the video channel Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage 16 ENInstalling Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec Basic Playback 20 ENVariable Speed Search Slow MotionHigh-Speed Turbo Search Pause during playback22 EN Skip SearchIndex Search Manual Index Mark/EraseNext Function Memory Digital TBC/NRRepeat Playback Manual TrackingAudio signal during TimeScan TimeScan24 EN Activate Variable Speed SearchTimeScan 26 EN Instant Timer Recording ITR Tape Remaining TimeEngage the Record-Pause mode 28 ENRetake Locate the start pointEngage the S-VHS ET mode Adjust the audio recording levelSuper VHS ET S-VHS ET Audio Recording Level ControlOn-screen Display Receiving Stereo and Bilingual ProgrammesReceived Playback RecordingAccess the Showview display Access the Showview screenAccess the Showview Program screen 32 ENSet the VPS/PDC mode Engage the recorder’s timer modeSatellite Receiver Users Guide Program Number SetExpress Timer Programming 34 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR+36 EN Cancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Overlapping programmes blink on the TV screenSelect the L-2 Select mode Recording modeProgramme Recording 38 ENRemote A/B Code Switching Remove the power supplySet the remote control code Re-supply the powerTV Multi-Brand Remote Control 40 ENSet the TV brand code Operate the TVSet the satellite receiver brand code Satellite Receiver Multi-Brand Remote ControlOperate the satellite receiver Navigation 42 ENNavigation Playback Check MemoryTurn Off Navigation Video Navigation Title ScreenCheck the memory Turn off NavigationAccess the Find Blank Space screen Edit Title44 EN Find Blank SpaceAccess the Edit Title screen Edit Tape TitleEntering Character Select the tape title46 EN Choice of CategorySelect the programme Enter the programme titleDelete Tape Data Delete Programme DataDelete the tape data Delete the programme dataAccess the Find Title screen Find Title48 EN Sort By Tape NumberAccess the Tape No. screen Access the Date screenSort By Date Select the programmeAccess the Category screen 50 ENSort By Category Category you want to watchSet the recorder’s input mode Set the edit modeEdit From a Camcorder Start the camcorderOutput/Input Set Select and L-2 Input Setting Decoder connectorAnother Video Recorder 54 ENRecorder Player Audio Dubbing 56 ENPre-recorded tape Audio-dubbed tape CD player, etcEngage the Audio Dubbing mode Start dubbingEnd Audio Dubbing Press AUX number key 0 and/or PR to select F-1 or S-1Insert Editing 58 ENSource tape Before Insert Editing Recording tape After Insert EditingEngage the Insert Editing mode AV Insert EditingLocate the end point Start EditingAccess the R.A.Edit screen 60 ENLoad the source cassette Start playback of the source cassetteMemory Capacity Prepare the recording deckStart Random Assemble Editing End Random Assemble Editing62 EN Start Synchro EditingPause Synchro Editing Press Synchro 7/79Access the Jlip ID No. Set screen Set the Jlip ID numberJlip ID Number ExamplesConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Satellite receiver Decoder Back of recorderSelect the input mode 66 ENConnect the decoder Set the tunerConnecting/Using a Stereo System Make connectionsMode Set Access the Mode Set screenSelect the mode Select the mode settingYou can set the B.E.S.T. Biconditional Equalised Signal This feature helps you to adjust the playback pictureWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder is70 EN For ExampleAbout Ntsc Playback Access the Auto Channel Set screen Tuner Set72 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice 74 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 76 ENSet Stations B TV Station And ID List Station NameAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 78 ENShowview System Setup Guide Program Number SetGuide Program Number Enter the Guide Program numberClock Set Access the Clock Set screen80 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationTroubleshooting 82 ENRecording Other Problems 84 ENPlayback 86 EN Preset Download Timer Warning Display TimeScan Tuner SetAV Insert Editing S.T. Picture System Clock SetInternational telephone Language code Country code