JVC LPT0328 specifications 78 EN, Access the Video Channel Set mode, Set the RF output system

Page 78

78 EN

SUBSIDIARY SETTINGS (cont.)

Video Channel Set

Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

If you have connected the recorder to your TV via the AV or S-VIDEO connection ( pg. 10, 11), since you do not need the video channel you have to set the video channel to off.

If you have connected the recorder to your TV via the RF connection ( pg. 10), you have to set the correct video channel.

Before performing the following steps:

Make sure the recorder’s power is off and there is no cassette inserted in the recorder.

A Access the Video Channel Set mode.

Hold down 0 on the recorder until the front display panel shows the following.

B Set the RF output system.

The blinking number on the display indicates the RF output system of your country.

●If you have selected MAGYARORSZÁG (36), CESKÁ REPUBLIKA (42), POLSKA (48), РОССИЯ (07) or OTHER EASTERN EUROPE (EE) for the country setting ( pg. 12, 16), press rt to set to “2”.

●For other countries, set to “1”. Then press OK. (1: B/G 2: D/K)

Then set your TV to UHF channel 50.

●If the two vertical white bars appear clearly on the TV screen as shown to the right, go to step 4.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

D Exit the Video Channel Set mode.

Press OK on the remote control.

C Set the video channel.

With AV or S-VIDEO Connection

Press PR – until the front display panel shows “1OUT– –” (or “2OUT– –”).

●Now the video channel is set to off.

With AV or S-VIDEO Connection

To view picture signals from the video recorder, set your TV to its AV mode.

With RF Connection

The channel on which the TV screen in step 3 appears clearly is your video channel.

To view picture signals from the video recorder, set your TV to the video channel.

With RF Connection

Press PR + or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area.

(Example) If channel 50 is available in your area

Page 77 Page 79
Image 78
Page 77 Page 79
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Inside View of Front Panel Rear View ON-SCREEN Display Remote Control How To Use Remote Control LCDSituate the recorder Check the contents10 EN Connect the recorder to TV8To connect to a TV with S-VIDEO/AUDIO in connectors Plug the end of the mains power cord into a mains outletVideo Connection Turn on the recorder Auto Set Up12 EN Select your countryPress rt to select your language code Perform Auto Set UpSelect the language Press rt to select Auto and press OK or eSet the video channel Perform Preset Download14 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 16 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 20 ENHigh-Speed Turbo Search Variable Speed SearchSlow Motion Pause during playbackIndex Search 22 ENSkip Search Manual Index Mark/EraseRepeat Playback Next Function MemoryDigital TBC/NR Manual Tracking24 EN Audio signal during TimeScanTimeScan Activate Variable Speed SearchTimeScan 26 EN Instant Timer Recording ITR Tape Remaining TimeRetake Engage the Record-Pause mode28 EN Locate the start pointSuper VHS ET S-VHS ET Engage the S-VHS ET modeAdjust the audio recording level Audio Recording Level ControlReceiving Stereo and Bilingual Programmes On-screen DisplayReceived Playback RecordingAccess the Showview Program screen Access the Showview displayAccess the Showview screen 32 ENSatellite Receiver Users Set the VPS/PDC modeEngage the recorder’s timer mode Guide Program Number SetExpress Timer Programming 34 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR+36 EN Select the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenProgramme Recording Select the L-2 Select modeRecording mode 38 ENSet the remote control code Remote A/B Code SwitchingRemove the power supply Re-supply the powerSet the TV brand code TV Multi-Brand Remote Control40 EN Operate the TVSatellite Receiver Multi-Brand Remote Control Set the satellite receiver brand codeOperate the satellite receiver Navigation Playback Navigation42 EN Check MemoryCheck the memory Turn Off NavigationVideo Navigation Title Screen Turn off Navigation44 EN Access the Find Blank Space screenEdit Title Find Blank SpaceEntering Character Access the Edit Title screenEdit Tape Title Select the tape titleSelect the programme 46 ENChoice of Category Enter the programme titleDelete the tape data Delete Tape DataDelete Programme Data Delete the programme data48 EN Access the Find Title screenFind Title Sort By Tape NumberSort By Date Access the Tape No. screenAccess the Date screen Select the programmeSort By Category Access the Category screen50 EN Category you want to watchEdit From a Camcorder Set the recorder’s input modeSet the edit mode Start the camcorderOutput/Input Set Select and L-2 Input Setting Decoder connectorAnother Video Recorder 54 ENRecorder Player Pre-recorded tape Audio-dubbed tape Audio Dubbing56 EN CD player, etcEnd Audio Dubbing Engage the Audio Dubbing modeStart dubbing Press AUX number key 0 and/or PR to select F-1 or S-1Source tape Before Insert Editing Recording tape Insert Editing58 EN After Insert EditingLocate the end point Engage the Insert Editing modeAV Insert Editing Start EditingLoad the source cassette Access the R.A.Edit screen60 EN Start playback of the source cassetteStart Random Assemble Editing Memory CapacityPrepare the recording deck End Random Assemble EditingPause Synchro Editing 62 ENStart Synchro Editing Press Synchro 7/79Jlip ID Number Access the Jlip ID No. Set screenSet the Jlip ID number ExamplesConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Satellite receiver Decoder Back of recorderConnect the decoder Select the input mode66 EN Set the tunerConnecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingWhen this function is set to ON, the timer is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture Off, and automatically disengaged when the recorder is70 EN For ExampleAbout Ntsc Playback 72 EN Access the Auto Channel Set screenTuner Set Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 74 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel76 EN Set Stations aSet Stations B TV Station And ID List Station NameVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 78 ENGuide Program Number Showview System SetupGuide Program Number Set Enter the Guide Program numberAccess the Clock Set screen Clock Set80 EN Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationTroubleshooting 82 ENRecording Other Problems 84 ENPlayback 86 EN AV Insert Editing S.T. Picture System Preset DownloadTimer Warning Display TimeScan Tuner Set Clock SetInternational telephone Language code Country code
Top Page Image Contents