JVC LPT0328 specifications Recording

Page 83

			EN 83
RECORDING
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Recording cannot be started.	● There is no cassette loaded, or the	Insert a cassette, or using adhesive tape,
		cassette loaded has had its record safety	cover the hole where the tab was
		tab removed.	removed.

2.	TV broadcasts cannot be recorded.	● “L-1”, “L-2”, “F-1”, “S-1” or “SAT” has	Set to the desired channel.
		been selected as the input mode.

3.	Tape-to-tape editing is not possible.	● The source (another video recorder,	Confirm that the source is properly
		camcorder) has not been properly	connected.
		connected.
		● All necessary power switches have not	Confirm that all units’ power switches are
		been turned on.	turned on.
		● The input mode is not correct.	Set the input mode to “L-1”, “L-2”, “F-1”
			or “S-1”.

4.	Camcorder recording is not possible.	● The camcorder has not been properly	Confirm that the camcorder is properly
		connected.	connected.
		● The input mode is not correct.	Set the input mode to “L-1”, “L-2”, “F-1”
			or “S-1”.

TIMER RECORDING
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Timer recording won’t work.	● The clock and/or the timer have been set	Re-perform the clock and/or timer
		incorrectly.	settings.
		● The timer is not engaged.	Press # and confirm that “#” is
			displayed on the front display panel.

2.	Timer programming is not possible.	● Timer recording is in progress.	Timer programming can’t be performed
			while a timer recording is in progress.
			Wait until it finishes.

3.	“#” and “[” on the front display	● The timer is engaged but there’s no	Load a cassette with the record safety tab
	panel won’t stop blinking.	cassette loaded.	intact, or cover the hole using adhesive
			tape.

4.	The power shuts off and “#” and	● The loaded cassette has had its record	Remove the cassette and cover the hole
	“[” on the front display panel won’t	safety tab removed.	with adhesive tape, or insert a cassette
	stop blinking.		with the record safety tab intact.
		● The end of the tape was reached during	The programme may not have been
		timer recording.	recorded in its entirety. Next time make
			sure you have enough time on the tape to
			record the entire programme.

5.	“#” blinks for 10 seconds and the	● # has been pressed when there are no	Check the programmed data and
	Timer mode is disengaged.	programs in memory, or the timer	re-program as necessary, then press #
		record information has been	again.
		programmed incorrectly.

6.	The SHOWVIEW system does not	● The recorder’s channel positions have	Refer to “Guide Program Number Set”
	timer-record properly.	been set incorrectly.	( pg. 79) and re-perform the procedure.

Image 83

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Inside View of Front Panel Rear View ON-SCREEN Display Remote Control Remote Control LCD How To UseConnect the recorder to TV Check the contents10 EN Situate the recorderVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsPlug the end of the mains power cord into a mains outlet Select your country Auto Set Up12 EN Turn on the recorderPress rt to select Auto and press OK or e Perform Auto Set UpSelect the language Press rt to select your language codePress rt to select CH - and press OK or e Perform Preset Download14 EN Set the video channelJust Clock Language for the on-screen display16 EN Access the Main Menu screenAccess the Country Set screen LanguageMake connections Installing Satellite ControllerSituate the Satellite Controller Attach the Satellite Controller18 EN Setting satellite receivers brand and channelVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link 20 EN Basic PlaybackPause during playback Variable Speed SearchSlow Motion High-Speed Turbo SearchManual Index Mark/Erase 22 ENSkip Search Index SearchManual Tracking Next Function MemoryDigital TBC/NR Repeat PlaybackActivate Variable Speed Search Audio signal during TimeScanTimeScan 24 ENTimeScan 26 EN Tape Remaining Time Instant Timer Recording ITRLocate the start point Engage the Record-Pause mode28 EN RetakeAudio Recording Level Control Engage the S-VHS ET modeAdjust the audio recording level Super VHS ET S-VHS ETReceived Receiving Stereo and Bilingual ProgrammesOn-screen Display Recording Playback32 EN Access the Showview displayAccess the Showview screen Access the Showview Program screenGuide Program Number Set Set the VPS/PDC modeEngage the recorder’s timer mode Satellite Receiver Users34 EN Express Timer ProgrammingPress PR+ To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel position36 EN Overlapping programmes blink on the TV screen Cancel or change programme settingConfirm the overlapping programmes Select the programme to modify38 EN Select the L-2 Select modeRecording mode Programme RecordingRe-supply the power Remote A/B Code SwitchingRemove the power supply Set the remote control codeOperate the TV TV Multi-Brand Remote Control40 EN Set the TV brand codeOperate the satellite receiver Satellite Receiver Multi-Brand Remote ControlSet the satellite receiver brand code Check Memory Navigation42 EN Navigation PlaybackTurn off Navigation Turn Off NavigationVideo Navigation Title Screen Check the memoryFind Blank Space Access the Find Blank Space screenEdit Title 44 ENSelect the tape title Access the Edit Title screenEdit Tape Title Entering CharacterEnter the programme title 46 ENChoice of Category Select the programmeDelete the programme data Delete Tape DataDelete Programme Data Delete the tape dataSort By Tape Number Access the Find Title screenFind Title 48 ENSelect the programme Access the Tape No. screenAccess the Date screen Sort By DateCategory you want to watch Access the Category screen50 EN Sort By CategoryStart the camcorder Set the recorder’s input modeSet the edit mode Edit From a CamcorderOutput/Input Set Decoder connector Select and L-2 Input Setting54 EN Another Video RecorderRecorder Player CD player, etc Audio Dubbing56 EN Pre-recorded tape Audio-dubbed tapePress AUX number key 0 and/or PR to select F-1 or S-1 Engage the Audio Dubbing modeStart dubbing End Audio DubbingAfter Insert Editing Insert Editing58 EN Source tape Before Insert Editing Recording tapeStart Editing Engage the Insert Editing modeAV Insert Editing Locate the end pointStart playback of the source cassette Access the R.A.Edit screen60 EN Load the source cassetteEnd Random Assemble Editing Memory CapacityPrepare the recording deck Start Random Assemble EditingPress Synchro 7/79 62 ENStart Synchro Editing Pause Synchro EditingExamples Access the Jlip ID No. Set screenSet the Jlip ID number Jlip ID NumberSimple Connections Connecting To a Satellite ReceiverSatellite receiver Decoder Back of recorder Perfect ConnectionsSet the tuner Select the input mode66 EN Connect the decoderMake connections Connecting/Using a Stereo SystemSelect the mode setting Mode SetAccess the Mode Set screen Select the modeOff, and automatically disengaged when the recorder is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture When this function is set to ON, the timer isFor Example 70 ENAbout Ntsc Playback Auto Channel Set Access the Auto Channel Set screenTuner Set 72 ENPress OK twice Perform Auto Channel SetView the Confirmation screen Manual Channel Set 74 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations B 76 ENSet Stations a Station Name TV Station And ID List78 EN Access the Video Channel Set modeExit the Video Channel Set mode Video Channel SetEnter the Guide Program number Showview System SetupGuide Program Number Set Guide Program Number80 EN Access the Clock Set screenClock Set Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock data82 EN TroubleshootingRecording 84 EN Other ProblemsPlayback 86 EN Clock Set Preset DownloadTimer Warning Display TimeScan Tuner Set AV Insert Editing S.T. Picture SystemCountry code International telephone Language code