JVC LPT0328 specifications Programme Recording, 38 EN, Select the L-2 Select mode, Recording mode

Page 38

38 EN

TIMER RECORDING (cont.)

Automatic Satellite

Programme

Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder’s AV2 (L-2) IN/DECODER connector and programme the timer on the satellite receiver. The recorder starts or stops recording by the signals input from the satellite receiver. After recording, the recorder’s power shuts off automatically.

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver’s power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Automatic Satellite Programme Recording mode; otherwise, the recorder will start recording when the connected appliance’s power is turned on.

●Automatic Satellite Programme Recording and timer-recording cannot be done at the same time.

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder’s AV2 (L-2) IN/DECODER connector. ( pg. 64, 65)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

A Select the L-2 SELECT mode.

SAT# indicator

NOTES:

Set “L-2 SELECT” to “A/V” or “SAT” ( pg. 53).

●When you select “SAT”, refer to “IMPORTANT” on page 64.

B Set the tape speed.

Press SP/LP/EP (p).

●It is not possible to select EP mode if “COLOUR SYSTEM” is set to “MESECAM”. ( pg. 71)

C Engage the Automatic Satellite Programme

Recording mode.

Press and hold SAT# for about 2 seconds. The SAT# indicator lights up and the recorder turns off automatically.

●To disengage the Automatic Satellite Programme Recording mode, press SAT#. The SAT# indicator goes off.

●If the recorder’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.

●In step 3, if the SAT# indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic

Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer Programming” ( pg. 34) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.

●The SAT# indicator blinks while Automatic Satellite Programme Recording is in progress.

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

●Pressing the recorder’s 1 button while Automatic Satellite Programme Recording is in progress turns off the recorder’s power and disengages the Automatic Satellite Programme Recording mode.

●If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible to set different tape speeds for each programme.

●Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not start Automatic Satellite Programme Recording even though the SAT# indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer.

●The B.E.S.T. system ( pg. 31) does not work while Automatic Satellite Programme Recording is in progress.

●Just Clock ( pg. 80) does not work when the Automatic Satellite Programme Recording mode is engaged.

●When the Automatic Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Automatic Satellite

Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON” ( pg. 69).

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Inside View of Front Panel Rear View ON-SCREEN Display Remote Control How To Use Remote Control LCDSituate the recorder Check the contents10 EN Connect the recorder to TVVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsPlug the end of the mains power cord into a mains outlet Turn on the recorder Auto Set Up12 EN Select your countryPress rt to select your language code Perform Auto Set UpSelect the language Press rt to select Auto and press OK or eSet the video channel Perform Preset Download14 EN Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockLanguage Access the Main Menu screenAccess the Country Set screen 16 ENAttach the Satellite Controller Installing Satellite ControllerSituate the Satellite Controller Make connectionsSetting satellite receivers brand and channel 18 ENVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link Basic Playback 20 ENHigh-Speed Turbo Search Variable Speed SearchSlow Motion Pause during playbackIndex Search 22 ENSkip Search Manual Index Mark/EraseRepeat Playback Next Function MemoryDigital TBC/NR Manual Tracking24 EN Audio signal during TimeScanTimeScan Activate Variable Speed SearchTimeScan 26 EN Instant Timer Recording ITR Tape Remaining TimeRetake Engage the Record-Pause mode28 EN Locate the start pointSuper VHS ET S-VHS ET Engage the S-VHS ET modeAdjust the audio recording level Audio Recording Level ControlReceived Receiving Stereo and Bilingual ProgrammesOn-screen Display Playback RecordingAccess the Showview Program screen Access the Showview displayAccess the Showview screen 32 ENSatellite Receiver Users Set the VPS/PDC modeEngage the recorder’s timer mode Guide Program Number SetExpress Timer Programming 34 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR+36 EN Select the programme to modify Cancel or change programme settingConfirm the overlapping programmes Overlapping programmes blink on the TV screenProgramme Recording Select the L-2 Select modeRecording mode 38 ENSet the remote control code Remote A/B Code SwitchingRemove the power supply Re-supply the powerSet the TV brand code TV Multi-Brand Remote Control40 EN Operate the TVOperate the satellite receiver Satellite Receiver Multi-Brand Remote ControlSet the satellite receiver brand code Navigation Playback Navigation42 EN Check MemoryCheck the memory Turn Off NavigationVideo Navigation Title Screen Turn off Navigation44 EN Access the Find Blank Space screenEdit Title Find Blank SpaceEntering Character Access the Edit Title screenEdit Tape Title Select the tape titleSelect the programme 46 ENChoice of Category Enter the programme titleDelete the tape data Delete Tape DataDelete Programme Data Delete the programme data48 EN Access the Find Title screenFind Title Sort By Tape NumberSort By Date Access the Tape No. screenAccess the Date screen Select the programmeSort By Category Access the Category screen50 EN Category you want to watchEdit From a Camcorder Set the recorder’s input modeSet the edit mode Start the camcorderOutput/Input Set Select and L-2 Input Setting Decoder connectorAnother Video Recorder 54 ENRecorder Player Pre-recorded tape Audio-dubbed tape Audio Dubbing56 EN CD player, etcEnd Audio Dubbing Engage the Audio Dubbing modeStart dubbing Press AUX number key 0 and/or PR to select F-1 or S-1Source tape Before Insert Editing Recording tape Insert Editing58 EN After Insert EditingLocate the end point Engage the Insert Editing modeAV Insert Editing Start EditingLoad the source cassette Access the R.A.Edit screen60 EN Start playback of the source cassetteStart Random Assemble Editing Memory CapacityPrepare the recording deck End Random Assemble EditingPause Synchro Editing 62 ENStart Synchro Editing Press Synchro 7/79Jlip ID Number Access the Jlip ID No. Set screenSet the Jlip ID number ExamplesConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Satellite receiver Decoder Back of recorderConnect the decoder Select the input mode66 EN Set the tunerConnecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingWhen this function is set to ON, the timer is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture Off, and automatically disengaged when the recorder is70 EN For ExampleAbout Ntsc Playback 72 EN Access the Auto Channel Set screenTuner Set Auto Channel SetPress OK twice Perform Auto Channel SetView the Confirmation screen 74 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations B 76 ENSet Stations a TV Station And ID List Station NameVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode 78 ENGuide Program Number Showview System SetupGuide Program Number Set Enter the Guide Program number80 EN Access the Clock Set screenClock Set Set the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationTroubleshooting 82 ENRecording Other Problems 84 ENPlayback 86 EN AV Insert Editing S.T. Picture System Preset DownloadTimer Warning Display TimeScan Tuner Set Clock SetInternational telephone Language code Country code
Top Page Image Contents