JVC LPT0345-001B Input receiving channel number, Engage timer recording standby mode, Press SP/EP

Page 25
GUIDE CHANNEL SET
GUIDE CH: 12
VCR CH : –––
PRESS NUMBER KEY (0–9)
OR (5,°), THEN (OK)
PRESS (PROG.) TO END

EN 25

4Input receiving channel number

The guide channel number, which is

assigned to the TV or cable station for the

PlusCode number that you entered in step 3, will appear automatically on the Guide Channel Set screen.

Press the Number keys (or CH +/– or SHUTTLE PLUS %Þ) to input the number of the channel on which the broadcast for the PlusCode number is received on the VCR or cable box, then press

OK.

The Guide Channel Set screen appears only when you input the PlusCode number of a station for which the guide channel number has not been set previously.

If you receive your channels with a cable box and if you have properly set your Controller, “CABLE CH” appears in place of “VCR CH”. If not, refer to pages 15 – 17.

7 Return to normal screen Press PROG. or OK.

“PROGRAM COMPLETED” appears on the screen for about 5 seconds, then normal screen appears.

•If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made.

The Program Check screen appears and conflicting programs will start blinking.

You can now correct the conflicting programs. See “When programs overlap each other” on page 37.

8Engage timer recording standby mode

Press TIMER.

The VCR turns off automatically and “ä” is displayed on the front display panel.

To use the VCR while it is in timer recording standby mode

Press TIMER to cancel the timer recording standby mode, then press POWER to turn on the VCR.

5 Check program date The PlusCode number you entered and the corresponding timer recording program is displayed on the Program screen. Check to make sure it is accurate.

PROGRAM 1

(VCR PLUS+ 12345678)

START

STOP

8:00PM

= 10:00PM

DATE

CH

12/24/00

12 SP

SUN

 

PRESS (8=DAILY, 9=WEEKLY STOP+/– = STOP TIME, SP/EP)

PRESS (PROG.) TO END

DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER after you use the VCR; otherwise, you cannot record the broadcasts you want.

When “AUTO TIMER” ( pg. 33) is set to “ON”, the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER to engage or disengage the timer recording standby mode.

To change the stop time, press STOP +/–. To timer-record daily (Monday–Friday) or weekly serials, press DAILY (M-F)(number “8”) or WEEKLY (number “9”). “DAILY” or “WEEKLY” appears on the Program screen. Pressing the button again makes each corresponding display disappear.

If you made a mistake, press CANCEL to access the VCR Plus+ screen again and input the correct PlusCode number.

If an incorrect PlusCode number or the one for a broadcast already finished has been inputted, “ERROR” is displayed for about 5 seconds, then the VCR Plus+ screen reappears.

6Set tape speed

Press SP/EP.

IMPORTANT

If you have moved to a different area or if a broadcasting station’s channel number has been changed, the wrong VCR CH or CABLE CH number will be displayed on the Program screen in step 5. When this happens, set the correct guide channel number for that station. ( pg. 32, “VCR Plus+ Setup”)

NOTES:

Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time, channel settings, and other menu settings are lost if it lasts for more than 3 minutes. As a result, when the power is supplied again to this VCR after the power failure, the following will take place.

1.This VCR starts the Plug & Play setting automatically to restore the clock time and channel setting.

2.If the clock time and channel setting are restored correctly, each timer program you have made will start unless its end

time already passes.

To timer-record cable channels received through a cable box, be sure to keep the cable box turned on with the correct channel selected.

Page 24 Page 26
Image 25
Page 24 Page 26
Contents HR-VP58U Telephone Number Dear CustomerPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents Page Situate VCR Check contentsConnect VCR to TV Final preparation for usePerform Plug & Play setup Plug & Play SettingClock and tuner channels will be set automatically Auto blinks Channel numbers are displayedAccess Main Menu screen Language SettingAccess Initial Set screen Select languagePreparations Clock SettingSelect clock set If you use a cable box, set the clock manually. pgSet Auto Clock to on Setting clock semiautomaticallySelect host channel Select time zoneSelect D.S.T. mode Setting clock manuallyManual Clock Set To make corrections any time during the processAccess Tuner Set screen Tuner SettingPerform Auto Channel Set Access Manual Channel Set screen Setting channels manuallyAdd or skip desired channels Manual Channel SetLoad a cassette Basic PlaybackStart playback Changing display information Basic Playback FeaturesChecking tape position Playing back tape repeatedlySelecting monitor sound Adjusting tracking conditionAutomatic operations after Access distant code Locating beginning of timerLocating beginning Start searchSelect recording channel Basic RecordingSet tape speed Start recordingEngage TV mode Basic Recording FeaturesSpecifying recording length Watching one program while recording anotherDisplay VCR status on TV screen Showing on-screen displayErase on-screen display Locating particular scene Special Effect Playback Rapidly Picture Search High-Speed Picture Search Variable-Speed Picture SearchSkipping unwanted portions Viewing still pictureViewing slow motion picture Pause during playbackVCR Plus+ Timer Programing To use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Press SP/EPVCR Plus+ guide channel matching VCR Plus+ SetupInput guide channel number Access Guide Channel Set screenExpress Timer Programing Press SP/EP to set the tape speed To timer-record daily Monday-Friday or weekly serialsDisengage timer Checking program settingsCancelingsettings or changing program Cancel or change program settingSelect program to modify Confirm overlapping programsOverlapping programs blink on the screen Change setting Useful Function SettingsSelect Function On the Remote Press OK or Shuttle Plus #When this function is set to OFF When this function is set to onWhen receiving a channel not in use Entire program while timer-recording in SP modeWhen stopping playback For Example2ND Audio Record Connection Edit To Or From AnotherTurn on the TV TV Brand SettingSet TV brand code Operate TVTurn on the cable box Cable Box Brand SettingEnter cable box brand code Operate cable boxTurn on the DBS receiver DBS Receiver Brand SettingEnter DBS receiver brand code Operate DBS receiverSet remote control code for Remote Changing Remote Control CodeUnplug VCR Plug in VCRPower 42EN Other Problems What happens if the tape reaches its end during recording? Can the VCR indefinitely remain in still mode?Repeat play List of termsRF connection Front display panel Front panelPage Page Specifications 50 EN Limited Warranty HR-VP68U
Top Page Image Contents