JVC LPT0345-001B manual When this function is set to on, When this function is set to OFF

Page 33

 

 

EN 33

 

 

* The default setting is bold in the table below.

 

 

AUTO PICTURE

When this function is set to “ON”, this VCR checks the condition of the

ON

 

tape in use during playback, and compensates to provide the highest-

 

possible playback pictures.

OFF

 

 

 

 

 

PICTURE CONTROL

This function helps you to adjust the playback picture quality according

AUTO (NORM): Normally select

to your preference.

 

this. Picture quality is

NOTES:

 

adjusted automatically.

 

When “AUTO PICTURE” is

When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not

 

“OFF”, “NORM” will appear

change until you select again.

 

instead of “AUTO”.

Select "EDIT" when you are dubbing tapes ( pg. 42 to 44). After you finish

EDIT:

Minimizes picture

dubbing the tapes, select “AUTO” (“NORM” when “AUTO PICTURE” is

 

degradation during editing

“OFF”.)

 

(recording and playback).

 

SOFT:

Reduces image

 

 

coarseness when viewing

 

 

overplayed tapes

 

 

containing much noise.

 

SHARP: Clearer, sharper-edged

 

 

picture when viewing

 

 

images with much flat,

 

 

same-colored surfaces

 

 

such as cartoons.

 

 

 

AUTO TIMER

When this function is set to “ON”:

ON

 

The timer recording standby mode is automatically engaged when the

 

VCR is turned off. It is temporarily canceled when the VCR is turned

OFF

 

 

on. You do not have to press TIMER to engage or disengage the timer

 

 

 

 

recording standby mode.

 

 

When this function is set to “OFF”:

 

 

You have to press TIMER to engage or disengage the timer recording

 

 

standby mode.

 

 

SUPERIMPOSE

When this function is set to “ON”, various VCR status information (on-

ON

 

screen display) appears on the screen.

OFF

 

NOTES:

 

 

 

 

When you use this VCR as the playback VCR for editing a tape, be sure to set

 

 

this function to “OFF”; otherwise, the VCR status information (on-screen

 

 

display) will be recorded on the edited tape.

 

 

If you select a channel on which no signal is received, the channel number is

 

 

displayed regardless of this function setting.

 

 

 

Image 33
Contents HR-VP58U Telephone Number Dear CustomerPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents Page Situate VCR Check contentsConnect VCR to TV Final preparation for usePerform Plug & Play setup Plug & Play SettingClock and tuner channels will be set automatically Auto blinks Channel numbers are displayedAccess Main Menu screen Language SettingAccess Initial Set screen Select languagePreparations Clock SettingSelect clock set If you use a cable box, set the clock manually. pgSet Auto Clock to on Setting clock semiautomaticallySelect host channel Select time zoneSelect D.S.T. mode Setting clock manuallyManual Clock Set To make corrections any time during the processTuner Setting Access Tuner Set screenPerform Auto Channel Set Access Manual Channel Set screen Setting channels manuallyAdd or skip desired channels Manual Channel SetBasic Playback Load a cassetteStart playback Changing display information Basic Playback FeaturesChecking tape position Playing back tape repeatedlyAdjusting tracking condition Selecting monitor soundAutomatic operations after Access distant code Locating beginning of timerLocating beginning Start searchSelect recording channel Basic RecordingSet tape speed Start recordingEngage TV mode Basic Recording FeaturesSpecifying recording length Watching one program while recording anotherShowing on-screen display Display VCR status on TV screenErase on-screen display Locating particular scene Special Effect PlaybackRapidly Picture Search High-Speed Picture Search Variable-Speed Picture SearchSkipping unwanted portions Viewing still pictureViewing slow motion picture Pause during playbackVCR Plus+ Timer Programing To use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Press SP/EPVCR Plus+ guide channel matching VCR Plus+ SetupInput guide channel number Access Guide Channel Set screenExpress Timer Programing Press SP/EP to set the tape speed To timer-record daily Monday-Friday or weekly serialsDisengage timer Checking program settingsCancelingsettings or changing program Cancel or change program settingConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen Change setting Useful Function SettingsSelect Function On the Remote Press OK or Shuttle Plus #When this function is set to OFF When this function is set to onWhen receiving a channel not in use Entire program while timer-recording in SP modeWhen stopping playback For Example2ND Audio Record Connection Edit To Or From AnotherTurn on the TV TV Brand SettingSet TV brand code Operate TVTurn on the cable box Cable Box Brand SettingEnter cable box brand code Operate cable boxTurn on the DBS receiver DBS Receiver Brand SettingEnter DBS receiver brand code Operate DBS receiverSet remote control code for Remote Changing Remote Control CodeUnplug VCR Plug in VCRPower 42EN Other Problems What happens if the tape reaches its end during recording? Can the VCR indefinitely remain in still mode?List of terms Repeat playRF connection Front display panel Front panelPage Page Specifications 50 EN Limited Warranty HR-VP68U