JVC LPT0345-001B manual DBS Receiver Brand Setting, Turn on the DBS receiver, Operate DBS receiver

Page 39

DBS Receiver Brand Setting

EN 39

This Remote can control some functions of the DBS (Direct Broadcast Satellite) receivers listed below.

1 Turn on the DBS receiver

Turn on the DBS receiver using the Power button on the DBS receiver or its Remote.

2Enter DBS receiver brand code

Follow the example shown below.

2–14

CABLE/DBS 1

4

7

1

2

5

8

0

3

POWER

2–2

3

 

2

2–3

6

 

 

 

9Number

4

2–4

ENTER

1Press and hold CABLE/DBS.

2 Press MBR SET.

3 Press the Number keys to enter your DBS receiver’s brand code by referring to the table below.

4 Press OK, and release CABLE/DBS.

The DBS receiver should turn off. If it does, try other operations below ( step 3).

Once you have set the Remote to operate the DBS receiver, you do not have to set it until you replace the batteries from the Remote.

3 Operate DBS receiver

While holding down CABLE/DBS, press one of the following buttons: POWER, TV CH +/–, and Number keys.

For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

To change the DBS receiver’s channels, press TV CH +/– or the Number keys. (The CH +/– button can be used to change the VCR’s

TV CH +/–

channels only.)

DBS BRAND NAME

BRAND CODE

 

 

JVC (DISH Network)

51

ECHOSTAR (DISH Network)

51

PRIMESTAR

50

SONY (DSS)

41

RCA (DSS)

40

 

 

NOTES:

Depending on the type of DBS receiver, some or all functions cannot be operated using this Remote.

It’s not possible to operate a DBS receiver not equipped with a remote sensor.

It's not possible to set the Remote for both your DBS receiver and a cable box at the same time. You can only set the Remote to operate one of these units at a time.

(Ex.) To set the Remote to JVC 51:

CABLE/

MBRSET

 

 

 

 

 

DBS

A/B

 

 

 

 

 

 

 

 

E

 

 

 

 

5

1

NTER/O

SD

Release

 

3

OK

Hold

Press in succession

 

 

 

down

 

 

 

 

 

 

Image 39
Contents HR-VP58U Telephone Number Dear CustomerGrounding or Polarization Power SourcesPower Lines Power Cord ProtectionReplacement Parts AccessoriesDamage Requiring Service CleaningContents Page Final preparation for use Check contentsSituate VCR Connect VCR to TVAuto blinks Channel numbers are displayed Plug & Play SettingPerform Plug & Play setup Clock and tuner channels will be set automaticallySelect language Language SettingAccess Main Menu screen Access Initial Set screenIf you use a cable box, set the clock manually. pg Clock SettingPreparations Select clock setSelect time zone Setting clock semiautomaticallySet Auto Clock to on Select host channelTo make corrections any time during the process Setting clock manuallySelect D.S.T. mode Manual Clock SetTuner Setting Access Tuner Set screenPerform Auto Channel Set Manual Channel Set Setting channels manuallyAccess Manual Channel Set screen Add or skip desired channelsBasic Playback Load a cassetteStart playback Playing back tape repeatedly Basic Playback FeaturesChanging display information Checking tape positionAdjusting tracking condition Selecting monitor soundAutomatic operations after Start search Locating beginning of timerAccess distant code Locating beginningStart recording Basic RecordingSelect recording channel Set tape speedWatching one program while recording another Basic Recording FeaturesEngage TV mode Specifying recording lengthShowing on-screen display Display VCR status on TV screenErase on-screen display Variable-Speed Picture Search Special Effect PlaybackLocating particular scene Rapidly Picture Search High-Speed Picture SearchPause during playback Viewing still pictureSkipping unwanted portions Viewing slow motion pictureVCR Plus+ Timer Programing Press SP/EP Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Input receiving channel numberVCR Plus+ guide channel matching VCR Plus+ SetupInput guide channel number Access Guide Channel Set screenExpress Timer Programing Press SP/EP to set the tape speed To timer-record daily Monday-Friday or weekly serialsCancel or change program setting Checking program settingsDisengage timer Cancelingsettings or changing programConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen On the Remote Press OK or Shuttle Plus # Useful Function SettingsChange setting Select FunctionWhen this function is set to OFF When this function is set to onFor Example Entire program while timer-recording in SP modeWhen receiving a channel not in use When stopping playback2ND Audio Record Connection Edit To Or From AnotherOperate TV TV Brand SettingTurn on the TV Set TV brand codeOperate cable box Cable Box Brand SettingTurn on the cable box Enter cable box brand codeOperate DBS receiver DBS Receiver Brand SettingTurn on the DBS receiver Enter DBS receiver brand codePlug in VCR Changing Remote Control CodeSet remote control code for Remote Unplug VCRPower 42EN Other Problems What happens if the tape reaches its end during recording? Can the VCR indefinitely remain in still mode?List of terms Repeat playRF connection Front display panel Front panelPage Page Specifications 50 EN Limited Warranty HR-VP68U