JVC LPT0345-001B manual 42EN

Page 42

42EN					TROUBLESHOOTING (cont.)

	TIMER RECORDING

		SYMPTOM		POSSIBLE CAUSE			CORRECTIVE ACTION
	1.	Timer recording will not work.		The clock and/or the timer have			Set the clock and/or timer correctly.
				been set incorrectly.
				The timer is not engaged.			Press TIMER and check to make sure
							that ä appears on the front display
							panel.
				The VCR has not been set up properly.			Re-perform the set-up procedures.
							Make sure you have compensated for
							guide channel and VCR or cable box
							channel number mismatches
							( pg. 26).

	2.	Timer programing will not work.		Timer recording is in progress.			Timer programing cannot be performed
							when timer recording is in progress.
							Wait until it finishes.

	3.	ä and ] on the front display		The timer is engaged but there is no			Load a cassette with the record safety
		panel will not stop blinking.		cassette loaded.			tab intact, or with the hole covered
							with adhesive tape.

	4.	The cassette is automatically		The loaded cassette has had its			Remove the cassette and cover its
		ejected, and ä and ] on the		record safety tab removed.			hole with adhesive tape, or replace it
		front display panel will not stop					with a cassette on which the safety
		blinking.					tab is intact.

	5.	ä blinks for 10 seconds and the		TIMER has been pressed when there			Check the programed data and set
		timer mode is disengaged.		are no programs in memory, or the			again if necessary, then press TIMER
				timer recording program has not			again.
				been set correctly.

	6.	The cassette is automatically		The tape reaches its end during			The program may not have been
		ejected, the power shuts off and ä		timer recording.			recorded in its entirety. Next time be
		and ] will not stop blinking.					sure you have enough time on the
							tape to record the entire broadcast.


	10.You moved, and now VCR Plus+			The receivable stations in the new			Re-perform the VCR Plus+ setup
		does not work properly.		area are received on different			procedure (	pg. 26).
				channels than those in the previous
				area.

	11.	“PROGRAM FULL” is displayed on		All 8 programs of the VCR’s timer			Wait until a space in memory clears,
		the screen.		memory are used.			or cancel unnecessary program
							information (	pg. 30).

CONTINUED ON NEXT PAGE \

Image 42

Contents HR-VP58U Dear Customer Telephone NumberPower Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Page Connect VCR to TV Check contentsSituate VCR Final preparation for useClock and tuner channels will be set automatically Plug & Play SettingPerform Plug & Play setup Auto blinks Channel numbers are displayedAccess Initial Set screen Language SettingAccess Main Menu screen Select languageSelect clock set Clock SettingPreparations If you use a cable box, set the clock manually. pgSelect host channel Setting clock semiautomaticallySet Auto Clock to on Select time zoneManual Clock Set Setting clock manuallySelect D.S.T. mode To make corrections any time during the processTuner Setting Access Tuner Set screenPerform Auto Channel Set Add or skip desired channels Setting channels manuallyAccess Manual Channel Set screen Manual Channel SetBasic Playback Load a cassetteStart playback Checking tape position Basic Playback FeaturesChanging display information Playing back tape repeatedlyAdjusting tracking condition Selecting monitor soundAutomatic operations after Locating beginning Locating beginning of timerAccess distant code Start searchSet tape speed Basic RecordingSelect recording channel Start recordingSpecifying recording length Basic Recording FeaturesEngage TV mode Watching one program while recording anotherShowing on-screen display Display VCR status on TV screenErase on-screen display Rapidly Picture Search High-Speed Picture Search Special Effect PlaybackLocating particular scene Variable-Speed Picture SearchViewing slow motion picture Viewing still pictureSkipping unwanted portions Pause during playbackVCR Plus+ Timer Programing Input receiving channel number Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Press SP/EPVCR Plus+ Setup VCR Plus+ guide channel matchingAccess Guide Channel Set screen Input guide channel numberExpress Timer Programing To timer-record daily Monday-Friday or weekly serials Press SP/EP to set the tape speedCancelingsettings or changing program Checking program settingsDisengage timer Cancel or change program settingConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen Select Function Useful Function SettingsChange setting On the Remote Press OK or Shuttle Plus #When this function is set to on When this function is set to OFFWhen stopping playback Entire program while timer-recording in SP modeWhen receiving a channel not in use For Example2ND Audio Record Edit To Or From Another ConnectionSet TV brand code TV Brand SettingTurn on the TV Operate TVEnter cable box brand code Cable Box Brand SettingTurn on the cable box Operate cable box Enter DBS receiver brand code DBS Receiver Brand Setting Turn on the DBS receiver Operate DBS receiverUnplug VCR Changing Remote Control CodeSet remote control code for Remote Plug in VCRPower 42EN Other Problems Can the VCR indefinitely remain in still mode? What happens if the tape reaches its end during recording?List of terms Repeat playRF connection Front panel Front display panelPage Page Specifications 50 EN Limited Warranty HR-VP68U