JVC HR-J260EK, HR-J465EK, HR-J265ES, HR-J265EK setup guide SET PDC Mode, Press TV Prog +/- to

Page 15

ENTER PRESET POSITION

 

Press TV PROG +/– to

 

– P1 –

 

enter the preset position

 

 

 

 

6 corresponding to the

START

STOP

21:00

= 22:00

 

broadcasting station you

SP

VPS/PDC OFF

 

wish to record.

 

 

 

 

DATE

TV PROG

 

 

 

25.12

1

 

 

 

[+/–] =

BBC 1

 

 

 

 

 

 

 

[PROG] : EXIT

 

 

SP

 

 

 

 

SET TAPE SPEED

 

7 Press SP/LP (

) to set the tape speed.

 

8

SET PDC MODE

 

Press PDC to select "ON" or "OFF".

 

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, PDC is set to ON.

If "VPS/PDC OFF" is displayed on the screen or "VPS/

 

PDC" is not lit on the display panel, PDC is set to OFF.

"PDC Recording" in the right column.

VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder.

RETURN TO NORMAL

SCREEN

9 After confirming all information is correct, press PROG or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears.

Repeat steps 1 9 for each additional programme.

ENGAGE RECORDER’S TIMER MODE

15

Satellite Receiver Users

To timer-record a satellite broadcast using Express Timer Programming:

1 Perform steps 1 10. Enter "L-2" for the preset position in step 6.

2 Set the satellite receiver to the appropriate channel before the selected programme begins.

3 Leave the satellite receiver's power on.

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service only in a very few areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel.

(step 8 in the left column).

NOTES:

Set the start time (PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 IN/DECODER on your recorder.

PDC recording is also possible via the AV1 IN/OUT connector.

10

Press

 

(TIMER). The recorder turns off automatically

 

and

 

 

 

 

appears on the display panel.

 

 

 

 

To disengage the timer, press

 

 

(TIMER) again.

 

 

To Timer-Record Weekly Or Daily Serials . . .

. . . anytime during steps 2 through 9, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday – Friday). Either "WEEKLY" or "DAILY"

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes.

WARNING– TIMER RECORDING

TO START SOON

[]

appears on the screen. Pressing the button again makes the corresponding indication disappear.

NOTE:

You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (pg. 16).

NOTES:

The warning only appears if you’re not in the Timer mode at the time.

If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .

Image 15
Contents HR-J465EK HR-J265EK HR-J260EK HR-J265ES Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Back of RecorderMains outlet Before performing the following procedure, make sure that Your TV via both an RF cable and a 21-pinGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search PlaybackActivate SLOW-MOTION Playback Recording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeVideo Plus+ Timer Programming Press SP/LP Timer WarningPDC Recording Satellite Receiver UsersEnter Programme Stop Time Express Timer ProgrammingEnter Programme Start TimePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Skip Over Unwanted Looking For Scene You WantActivate Index Search Activate Instant ReviewPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Satellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording Outdoor Unit Satellite CableBefore performing the following steps Press SP/LP on the remote control to set the tape speedMake Connections SET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderStart Recorder Edit From a CamcorderMode Start CamcorderScreen Access Mode SETSelect Picture Control SET Mode Adjust TrackingOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplaySelect Mode Auto SP→LP TimerAuto Timer Next Function Memory Activate RepeatRepeat Playback Ntsc PlaybackSET Video Channel Access Video CHAN- NEL SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Access Video Chan NEL SET ModeNEL SET Access Main MenuTuner Set Perform Auto ChanIs displayed on the screen Screen preset positionsProcedures After Scan CompletedStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Close Confirmation Access Manual Channel SET ScreenSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetEnter Guide Prog Number Video Plus+ SetupAccess Initial SET Screen Access Guide Prog SET ScreenQuestions And Answers Remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Camcorder recording is not possible Re-perform the clock and/or timer settingsFront View IndexTape Remaining Time Indicator displays time remaining AV2 IN/DECODER Connector enables connectionSymbolic Mode Indicators Programme Time Indicators show the programmeRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoMemo Memo VHF 44.5 143/143 470 MHz DA4 Double Azimuth helicalRotary two-head herical scan IN/OUT x 1, IN/DECODER x