JVC HR-J265ES Auto Tracking Button enables/disables auto, VCR, TV Prog +/-,TV +/-, TV Muting

Page 45

JVC TV. column.

)WEEKLY Button enables timer recording of weekly serials. ☞ pg. 13, 15

qAUX Button selects recorder's auxiliary input mode. ☞ pg. 22

w Button engages timer-standby mode.

☞pg. 13, 15

eDATE +/– Button inputs date of programme for timer recording. ☞ pg. 14

rTV PROG +/– Button — same as button on recorder. ☞ pg. 10

t30 SEC Button initiates a 30-second period of fast-motion playback. ☞ pg. 17

yAuto Tracking Button enables/disables auto

tracking mode during playback ☞ pg. 24

SP/LP () Button selects tape speed. ☞ pg. 10

uPlay Button — same as button on recorder. ☞ pg. 8, 9

iFast Forward Button — same as button on recorder. ☞ pg. 8, 9

oPause Button — same as button on recorder. ☞ pg. 9

pOK Button enters selections made in on-screen menus. ☞ pg. 18

Q @ #Button initiates functions such as Index Search ☞ pg. 17, variable-speed search, frame by frame playback. ☞ pg. 9

TV +/–Buttoncontrols volume of connected ☞ "Operating JVC TVs" in the right

45

How To Use

The remote control can operate most of your video recorder's functions, as well as basic functions of JVC TV sets. (See below.)

●Point the remote control toward the sensor window.

●The maximum operating distance of the remote control is about 8 m.

Operating JVC TVs

To operate your TV, while holding down the TV button, press the corresponding button: STANDBY/ON , TV/

VCR, TV PROG +/–,TV +/–, (TV Muting).

NOTES:

●When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover.

●Depending on the type of JVC TV, there may be cases where some or all functions cannot be operated using the remote control.

●If the remote control doesn't work properly, remove its batteries, wait a short time, replace the batteries and then try again.

Image 45

Contents HR-J465EK HR-J265EK HR-J260EK HR-J265ES Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Back of RecorderMains outlet Before performing the following procedure, make sure that Your TV via both an RF cable and a 21-pinGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search PlaybackActivate SLOW-MOTION Playback Recording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningSatellite Receiver Users Press SP/LPEnter Programme Express Timer ProgrammingStart Time Enter Programme Stop TimePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Activate Index Search Looking For Scene You WantActivate Instant Review Skip Over UnwantedPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Automatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Press SP/LP on the remote control to set the tape speedSET Edit Mode SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Make ConnectionsMode Edit From a CamcorderStart Camcorder Start RecorderSelect Picture Control SET Mode Access Mode SETAdjust Tracking ScreenAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsSelect Mode Auto SP→LP TimerAuto Timer Repeat Playback Activate RepeatNtsc Playback Next Function MemoryExit Video Channel SET Mode Access Video CHAN- NEL SET ModeVideo Channel Set SET Video ChannelWith RF Connection Access Video Chan NEL SET ModeTuner Set Access Main MenuPerform Auto Chan NEL SETProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Switch Stations Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetAccess Initial SET Screen Video Plus+ SetupAccess Guide Prog SET Screen Enter Guide Prog NumberQuestions And Answers Remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Camcorder recording is not possible Re-perform the clock and/or timer settingsFront View IndexSymbolic Mode Indicators AV2 IN/DECODER Connector enables connectionProgramme Time Indicators show the programme Tape Remaining Time Indicator displays time remainingRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoMemo Memo Rotary two-head herical scan DA4 Double Azimuth helicalIN/OUT x 1, IN/DECODER x VHF 44.5 143/143 470 MHz