JVC HR-J465EK, HR-J265ES Video Channel Set, Access Video CHAN- NEL SET Mode, SET Video Channel

Page 28

28SUBSIDIARYSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

DISPLAY

STANDBY/ON

TIMER

REC LINK

TV PROG

STOP

IMPORTANT

Perform the following steps only if —

Video Channel Set has not been done correctly by the Auto Set Up function (pg. 6).

interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.

If you have connected the video recorder to your TV via both an RF cable and a 21-pin SCART cable (AV connection), you do not need the video channel so you have to set the video channel to off. Go to "With AV Connection" below.

If you have connected the video recorder to your TV via an RF cable only (RF connection), you have to set the correct video channel Go to "With RF Connection" on page 29.

With AV Connection

Before performing the following procedure, make sure that:

the mains power cord is plugged into the mains outlet.

the video recorder is turned off and there is no cassette inserted in the recorder.

batteries have been installed in the remote control.

1 2 3

4 5 6

7 8 9

0

2

4

TV PROG

ACCESS VIDEO CHAN- NEL SET MODE

Press and hold down STOP on the recorder until the

1 display panel shows the following.

SET VIDEO CHANNEL

Press TV PROG – until the display panel shows

1

?

OK

2 "OUT– –".

Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 28
Contents HR-J465EK HR-J265EK HR-J260EK HR-J265ES Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Back of TVMains outlet Your TV via both an RF cable and a 21-pin Before performing the following procedure, make sure thatGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackPlayback Activate HIGH-SPEED SearchActivate SLOW-MOTION Playback Recording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingSatellite Receiver Users Press SP/LPExpress Timer Programming Enter ProgrammeStart Time Enter Programme Stop TimeSET PDC Mode Press TV Prog +/- toCheck, Cancel And Replace Programmes Looking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Playback RecordingOr press Record on the recorder Aerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitPress SP/LP on the remote control to set the tape speed Before performing the following stepsSET Recording DECK’S Input Mode SET Edit ModeEdit To Or From Another Video Recorder Make ConnectionsEdit From a Camcorder ModeStart Camcorder Start RecorderAccess Mode SET Select Picture Control SET ModeAdjust Tracking ScreenAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto SP→LP Timer Select ModeAuto Timer Activate Repeat Repeat PlaybackNtsc Playback Next Function MemoryAccess Video CHAN- NEL SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelAccess Video Chan NEL SET Mode With RF ConnectionAccess Main Menu Tuner SetPerform Auto Chan NEL SETScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Fine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Access Manual Channel SET Screen Switch StationsSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup Access Initial SET ScreenAccess Guide Prog SET Screen Enter Guide Prog NumberRemain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Re-perform the clock and/or timer settings Camcorder recording is not possibleIndex Front ViewAV2 IN/DECODER Connector enables connection Symbolic Mode IndicatorsProgramme Time Indicators show the programme Tape Remaining Time Indicator displays time remainingRemote Control Auto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingMemo Memo DA4 Double Azimuth helical Rotary two-head herical scanIN/OUT x 1, IN/DECODER x VHF 44.5 143/143 470 MHz