JVC HR-J265ES, HR-J465EK, HR-J265EK, HR-J260EK setup guide Before performing the following steps

Page 21

21

DISPLAY

STANDBY/ON

TIMER

 

REC LINK

TV PROG

REC

LINK

 

1 2 3

2

4 5 6

7 8 9

Before performing the following steps:

Make sure the satellite receiver is connected to the recorder's AV2 IN/DECODER connector. (pg. 20)

Programme the timer on the satellite receiver.

Insert a cassette with the safety tab in place.

SET TAPE SPEED

1 Press SP/LP () on the remote control to set the tape speed.

ENGAGE AUTO SATELLITE PROG REC MODE

2 Press and hold REC LINK for about 2 seconds. The indicator lights up and the recorder turns off automati- cally.

To disengage the Auto Satellite Prog Rec mode, press REC LINK. The indicator goes off.

If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

0

4

SP/LP

1

?

3

NOTES:

ATTENTION

Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.

If you have connected another appliance other than a satellite receiver to the AV2 IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

Auto Satellite Prog recording and timer-recording cannot be done at the same time.

When you press and hold the recorder's REC LINK button to engage the Auto Satellite Prog Rec mode, if the REC LINK indicator does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*.

If this is the case, perform "Express Timer Programming" (pg.14) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.

Auto Satellite Prog recording is possible with the AV2 IN/DECODER connector only.

When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function (pg. 17).

For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.

The REC LINK indicator blinks while Auto Satellite Prog recording is in progress.

Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode.

If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 1 will apply to all the programmes for Auto Satellite Prog recording.

The B.E.S.T. system (pg. 18) does not work while Auto Satellite Prog recording is in progress.

Just Clock (pg. 37) does not work when the Auto Satellite Prog Rec mode is engaged.

Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme.

If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 IN/DECODER connector.

Image 21
Contents HR-J465EK HR-J265EK HR-J260EK HR-J265ES Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Back of RecorderMains outlet Before performing the following procedure, make sure that Your TV via both an RF cable and a 21-pinGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search PlaybackActivate SLOW-MOTION Playback Recording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningSatellite Receiver Users Press SP/LPEnter Programme Express Timer ProgrammingStart Time Enter Programme Stop TimePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Activate Index Search Looking For Scene You WantActivate Instant Review Skip Over UnwantedPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Automatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Press SP/LP on the remote control to set the tape speedSET Edit Mode SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Make ConnectionsMode Edit From a CamcorderStart Camcorder Start RecorderSelect Picture Control SET Mode Access Mode SETAdjust Tracking ScreenAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsSelect Mode Auto SP→LP TimerAuto Timer Repeat Playback Activate RepeatNtsc Playback Next Function MemoryExit Video Channel SET Mode Access Video CHAN- NEL SET ModeVideo Channel Set SET Video ChannelWith RF Connection Access Video Chan NEL SET ModeTuner Set Access Main MenuPerform Auto Chan NEL SETProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Switch Stations Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetAccess Initial SET Screen Video Plus+ SetupAccess Guide Prog SET Screen Enter Guide Prog NumberQuestions And Answers Remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Camcorder recording is not possible Re-perform the clock and/or timer settingsFront View IndexSymbolic Mode Indicators AV2 IN/DECODER Connector enables connectionProgramme Time Indicators show the programme Tape Remaining Time Indicator displays time remainingRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoMemo Memo Rotary two-head herical scan DA4 Double Azimuth helicalIN/OUT x 1, IN/DECODER x VHF 44.5 143/143 470 MHz