JVC HR-J265ES, HR-J465EK, HR-J265EK, HR-J260EK setup guide Back of TV, Back of Recorder, Mains outlet

Page 5

5

STEP

2

INSTALLATION

CONNECT VIDEO RECORDER TO TV

Place the recorder on a stable, flat surface.

Back of TV

Aerial connector

21-pin AV input connector (SCART)

Mains Power Cord

RF Cable (provided)

21-pin SCART Cable (not provided)

TV Aerial Cable

(not provided)

Make this

connection if your TV has a

21-pin AV input connector (SCART) in order to reduce the possibility of interference. And if you are using a stereo TV, you will need this cable in order to enjoy stereo playback of videotapes.

		ENTREE
		ANT. IN
AV2 ENTREE/DECODEUR	AV1 ENTREE/SORTIE	ANTENNE
IN/DECODER	IN/OUT	SORTIE
		OUT

Back of Recorder

Mains outlet

RF CONNECTION

To Connect To A TV With NO 21-pin AV input connector (SCART) . . .

1– Disconnect the TV aerial cable from the TV.

2– Connect the TV aerial cable to the ANT. IN jack on the rear panel of the recorder.

3– Connect the provided RF cable between the RF. OUT jack on the rear panel of the recorder and the TV’s aerial connector.

AV CONNECTION

To Connect To A TV With 21-pin AV input connector (SCART) . . .

1– Connect the aerial, recorder and TV as per “RF

CONNECTION”.

2– Connect an optional SCART cable between the AV1 IN/OUT connector on the rear panel of the recorder and the TV’s 21-pin AV input connector (SCART).

ATTENTION

■Do NOT Plug the mains power cord into a mains outlet until all connections are completed.

■Do NOT press the button on the recorder or on the remote control to turn on the recorder's power before you start the Auto Set Up procedure described on page 6.

AFTER YOU FINISH THIS STEP

Go to Step 3 – AUTO SET UP

Image 5

Contents HR-J465EK HR-J265EK HR-J260EK HR-J265ES Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Mains outlet Back of TVBack of Recorder Go to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate SLOW-MOTION Playback Activate HIGH-SPEED SearchPlayback Recording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningSatellite Receiver Users Press SP/LPEnter Programme Express Timer ProgrammingStart Time Enter Programme Stop TimePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Activate Index Search Looking For Scene You WantActivate Instant Review Skip Over UnwantedS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Automatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Press SP/LP on the remote control to set the tape speedSET Edit Mode SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Make ConnectionsMode Edit From a CamcorderStart Camcorder Start RecorderSelect Picture Control SET Mode Access Mode SETAdjust Tracking ScreenAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Select ModeAuto SP→LP Timer Repeat Playback Activate RepeatNtsc Playback Next Function MemoryExit Video Channel SET Mode Access Video CHAN- NEL SET ModeVideo Channel Set SET Video ChannelWith RF Connection Access Video Chan NEL SET ModeTuner Set Access Main MenuPerform Auto Chan NEL SETProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Switch Stations Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetAccess Initial SET Screen Video Plus+ SetupAccess Guide Prog SET Screen Enter Guide Prog NumberWhat happens if the tape runs out during recording? Questions And AnswersRemain lit on the display panel. Is there Problem? Troubleshooting Camcorder recording is not possible Re-perform the clock and/or timer settingsFront View IndexSymbolic Mode Indicators AV2 IN/DECODER Connector enables connectionProgramme Time Indicators show the programme Tape Remaining Time Indicator displays time remainingRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoMemo Memo Rotary two-head herical scan DA4 Double Azimuth helicalIN/OUT x 1, IN/DECODER x VHF 44.5 143/143 470 MHz