JVC HR-J465EK, HR-J265ES, HR-J265EK, HR-J260EK setup guide Troubleshooting

Page 40

40

SUBSIDIARYINFORMATION(cont.)

Troubleshooting

Before requesting service for a problem, use this chart to see if you can correct the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair.

POWER

SYMPTOM

1.No power is applied to the recorder.

2.The clock is functioning properly, but the recorder cannot be powered.

3.The remote control won’t function.

TAPE TRANSPORT

SYMPTOM

1.The tape does not run during recording.

2.The tape will not rewind or fast- forward.

PLAYBACK

SYMPTOM

1.The playback picture does not appear while the tape is running.

2.Noise appears during visual search.

3.Noise appears during normal playback.

4.The playback picture is blurred or interrupted while TV broadcasts are clear.

5.Breaks are noticeable in Hi-Fi soundtrack.

RECORDING

SYMPTOM

1.Recording cannot be started.

2.TV broadcasts cannot be recorded.

3.Tape-to-tape editing is not possible.

POSSIBLE CAUSE

The mains power cord is disconnected.

“ is displayed on the display panel with Auto Timer set to "OFF".

The batteries are discharged.

POSSIBLE CAUSE

“ is displayed on the display panel.

The tape is already fully rewound or fast-forwarded.

POSSIBLE CAUSE

If you’re using the RF OUT connec- tion . . .

. . . the TV receiver’s channel selector is not set to the VIDEO channel.

. . . the recorder's VIDEO channel has not been correctly set.

If you’re using the AV connection, the TV receiver is not set to the AV mode.

This is normal.

The automatic tracking mode is engaged.

The video heads may be dirty.

Automatic tracking is engaged.

POSSIBLE CAUSE

There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed.

“L-1” or “L-2” has been selected as the input mode.

The source (another video recorder, camcorder) has not been properly connected.

All necessary power switches have not been turned on.

The input mode is not correct.

CORRECTIVE ACTION

Connect the mains power cord.

Press the button to turn the “ “ indicator off.

Replace the dead batteries with new ones.

CORRECTIVE ACTION

Press PLAY to turn the ““ indicator off.

Check the cassette.

CORRECTIVE ACTION

If you are using the RF OUT connec- tion . . .

. . . set the TV receiver to the VIDEO channel. (pg. 6)

. . . Perform "Video Channel Set" (pg. 28)

If you are using the AV connection, set the TV to its AV mode.

Try manual tracking (pg. 24).

Consult your JVC dealer.

Engage and adjust tracking manually. (pg. 24)

CORRECTIVE ACTION

Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed.

Set to the desired preset.

Confirm that the source is properly connected.

Confirm that all units’ power switches are turned on.

Set the input mode to “L-1” or “L-2”.

Image 40
Contents HR-J465EK HR-J265EK HR-J260EK HR-J265ES Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Back of TVMains outlet Your TV via both an RF cable and a 21-pin Before performing the following procedure, make sure thatGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackPlayback Activate HIGH-SPEED SearchActivate SLOW-MOTION Playback Recording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingSatellite Receiver Users Press SP/LPExpress Timer Programming Enter ProgrammeStart Time Enter Programme Stop TimeSET PDC Mode Press TV Prog +/- toCheck, Cancel And Replace Programmes Looking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Playback RecordingOr press Record on the recorder Aerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitPress SP/LP on the remote control to set the tape speed Before performing the following stepsSET Recording DECK’S Input Mode SET Edit ModeEdit To Or From Another Video Recorder Make ConnectionsEdit From a Camcorder ModeStart Camcorder Start RecorderAccess Mode SET Select Picture Control SET ModeAdjust Tracking ScreenAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto SP→LP Timer Select ModeAuto Timer Activate Repeat Repeat PlaybackNtsc Playback Next Function MemoryAccess Video CHAN- NEL SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelAccess Video Chan NEL SET Mode With RF ConnectionAccess Main Menu Tuner SetPerform Auto Chan NEL SETScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Fine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Access Manual Channel SET Screen Switch StationsSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup Access Initial SET ScreenAccess Guide Prog SET Screen Enter Guide Prog NumberRemain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Re-perform the clock and/or timer settings Camcorder recording is not possibleIndex Front ViewAV2 IN/DECODER Connector enables connection Symbolic Mode IndicatorsProgramme Time Indicators show the programme Tape Remaining Time Indicator displays time remainingRemote Control Auto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingMemo Memo DA4 Double Azimuth helical Rotary two-head herical scanIN/OUT x 1, IN/DECODER x VHF 44.5 143/143 470 MHz