JVC HR-J465EK, HR-J265ES, HR-J265EK, HR-J260EK setup guide Remote Control

Page 44

^ STANDBY/ON recorder.

44SUBSIDIARYINFORMATION(cont.)

REMOTE CONTROL

1 TV Button enables remote control of your JVC

TV. ☞ "Operating JVC TVs" on page 45.

2 TV/VCR Button switches connected TV's mode

1

2

3

4

5

6

7

8

9

0

!

@

#

$

%

TV

TV/VCR AUDIO – –:– –

1	2	3
		2
4	5	6
VPS/PDC	DAILY/QTDN. WEEKLY/HEBDO
7	8	9
0000	AUX
	0	4
		4
START	STOP DATE	TV
DEBUT	FIN	PROG
	EXPRESS
1 PROG	?	30 SEC

	MENU	3	OK
	MENU	TV PROG +	OK
		TV PROG +
	V		+
	T
	–		TV

	^	between TV and AV. ☞ pg. 8, 10 and "Operat-
	&	ing JVC TVs" on page 45.
	&	3 REVIEW Button "reviews" timer-recorded
		3 REVIEW Button "reviews" timer-recorded

*programme. ☞ pg. 17

(4 NUMBER Keys are used in preset position

	)	selection ☞ pg. 10, VIDEO Plus+ timer pro-
		gramming ☞ pg. 12.
	q
		5 PDC Button enables/disables PDC recording.
	w
		☞ pg. 13, 15

e* VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder.

r6 Button cancels timer-programme. ☞ pg. 16

t0000 Button resets counter to 0:00:00. ☞ pg. 11

y7 STOP +/– Button inputs programme Stop Time.

u		☞ pg. 14
i	8 START +/– Button accesses Regular Program
		screen; inputs programme Start Time. ☞ pg. 14
o
	9 PROG Button accesses VIDEO Plus+ Program
p		screen. ☞ pg. 12
	0				Button accesses Program screens/displays

to check the programme that you have pro-

Q	grammed (next programme's information screen

TV PROG –

appears each time button is pressed). ☞ pg. 16

! Rewind [REW] Button — same as button on

Buttons with a small dot on the left side of the name can also be used to operate your JVC TV while holding down the TV button.

☞"Operating JVC TVs" on page 45.

recorder. ☞ pg. 8, 9

@Record Button — same as button on recorder. ☞ pg. 10

#Stop Button — same as button on recorder. ☞ pg. 8

$MENU Button accesses Menu screen. ☞ pg. 18 % %Þ Button is used for selection in on-screen

menus. ☞ pg. 18

TV PROG +/– selects the connected JVC TV's channel. ☞ "Operating JVC TVs" on page 45.

Button — same as button on

This remote control transmits A code signals only; it is not applicable to B code signals.

& (TV Muting) Button mutes sound of connected JVC TV. ☞ "Operating JVC TVs" on page 45.

*Display (– –:– –) Button — same as button on recorder.

☞ pg. 11

(DAILY Button enables timer recording of daily serials. ☞ pg. 13, 15

Image 44

Contents HR-J465EK HR-J265EK HR-J260EK HR-J265ES Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Mains outlet Back of TVBack of Recorder Go to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackActivate SLOW-MOTION Playback Activate HIGH-SPEED SearchPlayback Recording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingSatellite Receiver Users Press SP/LPExpress Timer Programming Enter ProgrammeStart Time Enter Programme Stop TimeSET PDC Mode Press TV Prog +/- toCheck, Cancel And Replace Programmes Looking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Aerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitPress SP/LP on the remote control to set the tape speed Before performing the following stepsSET Recording DECK’S Input Mode SET Edit ModeEdit To Or From Another Video Recorder Make ConnectionsEdit From a Camcorder ModeStart Camcorder Start RecorderAccess Mode SET Select Picture Control SET ModeAdjust Tracking ScreenAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Select ModeAuto SP→LP Timer Activate Repeat Repeat PlaybackNtsc Playback Next Function MemoryAccess Video CHAN- NEL SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelAccess Video Chan NEL SET Mode With RF ConnectionAccess Main Menu Tuner SetPerform Auto Chan NEL SETScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Access Manual Channel SET Screen Switch StationsSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup Access Initial SET ScreenAccess Guide Prog SET Screen Enter Guide Prog NumberWhat happens if the tape runs out during recording? Questions And AnswersRemain lit on the display panel. Is there Problem? Troubleshooting Re-perform the clock and/or timer settings Camcorder recording is not possibleIndex Front ViewAV2 IN/DECODER Connector enables connection Symbolic Mode IndicatorsProgramme Time Indicators show the programme Tape Remaining Time Indicator displays time remainingRemote Control Auto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingMemo Memo DA4 Double Azimuth helical Rotary two-head herical scanIN/OUT x 1, IN/DECODER x VHF 44.5 143/143 470 MHz