JVC HR-J260EK Questions And Answers, What happens if the tape runs out during recording?

Page 39

SUBSIDIARYINFORMATION39

Questions And Answers

PLAYBACK

Q. What happens if the end of the tape is reached during playback or search?

A.The tape is automatically rewound to the beginning.

Q.Can the video recorder indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.During search, slow, still and frame-by-frame playback, I can’t hear any audio. What’s the problem?

A.This is normal.

Q.When returning from variable-speed search to normal playback, the picture is disturbed. Should I be concerned about this?

A.No, it is normal.

Q.Noise bars appear during variabl-speed search. What’s the problem?

A.This is normal.

Q.Other than preventing further recording, what effect does removing the Record Safety tab have?

A.It disables marking of index codes.

Q.Sometimes, during Index Search, the video recorder can’t find the programme I want to see. Why not?

A.There may be index codes too close together.

RECORDING

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?

A.This is normal. It reduces distortion at the pause and resume points.

Q.Can the video recorder indefinitely remain in the Record-Pause mode?

A.No. The video recorder shuts off automatically after 5 minutes to protect the heads.

Q.What happens if the tape runs out during recording?

A.The video recorder automatically rewinds it to the beginning or, if Timer Recording, the cassette is ejected.

TIMER RECORDING

Q. "" and " " remain lit on the display panel. Is there

a problem?

A.No. This is a normal condition for a timer recording in progress.

Q.Can I programme the timer while I’m watching a tape or a TV broadcast?

A.You won’t see the picture as it is replaced by the on- screen menu, but the audio from the program or tape you’re viewing can be heard.

Q.Is it possible to timer-record a TV programme broadcast in 2000?

A.Yes, it is possible.

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 39
Contents HR-J465EK HR-J265EK HR-J260EK HR-J265ES Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Back of RecorderMains outlet Before performing the following procedure, make sure that Your TV via both an RF cable and a 21-pinGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search PlaybackActivate SLOW-MOTION Playback Recording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeVideo Plus+ Timer Programming Press SP/LP Timer WarningPDC Recording Satellite Receiver UsersEnter Programme Stop Time Express Timer ProgrammingEnter Programme Start TimePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Skip Over Unwanted Looking For Scene You WantActivate Index Search Activate Instant ReviewPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Satellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording Outdoor Unit Satellite CableBefore performing the following steps Press SP/LP on the remote control to set the tape speedMake Connections SET Recording DECK’S Input ModeSET Edit Mode Edit To Or From Another Video RecorderStart Recorder Edit From a CamcorderMode Start CamcorderScreen Access Mode SETSelect Picture Control SET Mode Adjust TrackingOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplaySelect Mode Auto SP→LP TimerAuto Timer Next Function Memory Activate RepeatRepeat Playback Ntsc PlaybackSET Video Channel Access Video CHAN- NEL SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Access Video Chan NEL SET ModeNEL SET Access Main MenuTuner Set Perform Auto ChanIs displayed on the screen Screen preset positionsProcedures After Scan CompletedStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Close Confirmation Access Manual Channel SET ScreenSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetEnter Guide Prog Number Video Plus+ SetupAccess Initial SET Screen Access Guide Prog SET ScreenQuestions And Answers Remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Camcorder recording is not possible Re-perform the clock and/or timer settingsFront View IndexTape Remaining Time Indicator displays time remaining AV2 IN/DECODER Connector enables connectionSymbolic Mode Indicators Programme Time Indicators show the programmeRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoMemo Memo VHF 44.5 143/143 470 MHz DA4 Double Azimuth helicalRotary two-head herical scan IN/OUT x 1, IN/DECODER x